Télécharger Imprimer la page

Aqua Medic SR 400 Mode D'emploi page 4

Sulphur reactor

Publicité

Les langues disponibles
  • FR

Les langues disponibles

The Aqua Medic Sulphur Reactor SR 400 is equipped with two tube connections and can be used
as outside or inside filter. The filter is installed with the enclosed holder at a horizontal brace or the
aquarium glass. The filter is connected via a tube and a bypass T-piece to a pump with a sufficient
flow rate. The water should flow upwards through the filter.
The Sulphur Reactor SR 400 is filled with sulphur beads which serve as food and growth
substrate for the bacteria. The water flow through the system is very slow, approx. one
drop/second and the water depletes of oxygen. In the Sulphur Reactor, special bacteria reduce
nitrate by oxydizing sulphur in an oxygen-free environment. The residue is nitrogen gas that
escapes into the environment.
Installation
The attached holder makes a simple installation of the filter in or at the aquarium possible. The
upper holder plate and all screws have to be removed. Then, the holder can be shoved on a
horizontal brace in the aquarium or on an aquarium glass. It is fixed with two screws. The Sulphur
Reactor SR 400 can be connected to a separate pump or every standard outside filter via a 6/4
tube and the included T-piece. We recommend to install an adjusting tap behind the T-piece in the
pressure pipe. By easy closing of this tap, the pressure will increase toward the nitrate filter and
saves constant adjustment of the flow rate.
Before the first operation, the filter should be rinsed with water to avoid cloudings through possible
residual particles of the filter material. The granules included in the Sulphur Reactor are suitable
for fresh and salt water.
In particular during the start phase, the nitrate and nitrite content of the outflowing water should
be checked regularly. If larger quantities of nitrite are proved, the flow rate has to be reduced. The
outflowing water is strongly sour since the bacteria produce sulphuric acid with this kind of
decomposition. This would lower the pH-value and carbonate hardness of the aquarium water. In
order to prevent this, a reactor filled with calcium carbonate can be connected at the outlet side
(available as accessory). This reactor would convert the sulphuric acid into calcium sulfate. Thus,
the total hardness would increase in fresh water, in salt water the calcium content would rise.
If a part of the sulphur beads has been used by bacteria, they have to be replaced – or better, the
whole content should be renewed. For replacing the granules, unscrew one of the two connecting
pieces and shake the used granules out. Residual particles are removed by rinsing with water.
Then, the filter can be filled with new material. So that the device shuts tightly, the thread has to
be cleaned from remaining sulphur beads with water. Do not forget the sealing ring when screwing
in the connecting piece!
Available spare parts: Please refer to www.aqua-medic.de.
Warranty
Should any defect in materials or workmanship be found within 24 months of the date of purchase
AB Aqua Medic undertakes to repair, or at our option replace, the defective part free of charge –
always provided the product has been installed correctly, is used for the purpose that was intended
by us, is used in accordance with the operating instructions and is returned to us carriage paid.
Proof of Purchase is required by presentation of the original invoice or receipt indicating the
dealer's name, the model number and date of purchase. This warranty may not apply if any model
or production number has been altered, deleted or removed, unauthorised persons or organisations
have executed repairs, modifications or alterations, or damage is caused by accident, misuse or
neglect. Please note that the product is not defective under the terms of this Warranty where the
product, or any of its component parts, was not originally designed and / or manufactured for the
market in which it is used. These statements do not affect your statutory rights as a customer.
AB Aqua Medic GmbH - Gewerbepark 24 - 49143 Bissendorf/Germany
- Technical changes reserved - 07/2016
4

Publicité

loading