Publicité
Les langues disponibles
Les langues disponibles
REFRACTOR
AND
REFLECTOR
INSTALLATION
1. Apply a small amount of HTL® lubricant to threads of
refractor or reflector lens.
2. Install GR/PGR series refractor or GRD4 reflector
lens on luminaire by placing over lamp and hand
tighten onto ballast housing.
3. Follow the instructions furnished with refractor and
reflector lens for complete installation and
adjustment information.
4. PGR series plastic refractors are not suitable for
hazardous (classified) locations.
MAINTENANCE
• Perform visual, electrical, and mechanical inspections
on a regular basis. The environment and frequency of
use should determine this. However, it is recommended
that checks be made at least once a year. We
recommend an Electrical Preventive Maintenance
Program as described in the National Fire Protection
Association Bulletin NFPA No. 70B: Recommended
Practice For Electrical Equipment Maintenance
(www.nfpa.org).
• The globe (and guard and reflector when used),
refractor or reflector lens should be cleaned periodically
to insure continued lighting performance. To clean, wipe
the reflector, then the globe with a clean damp cloth. If
this is not sufficient, use a mild soap or a liquid cleaner
such as Collinite NCF or Duco #7. Do not use an
abrasive, strong alkaline, or acid cleaner. Damage may
result.
FIELD ASSEMBLED LUMINAIRES
Champ DMV Series Luminaires.
Complete luminaire consists of cover, ballast housing and globe with or without guard or reflector.
IF 1083 • 03/11
Copyright
LENS
• Visually check for undue heating evidenced by
discoloration of wires or other components, damaged
parts, or leakage evidenced by water or corrosion
in the interior. Replace all worn, damaged, or
malfunctioning components and clean gasket seals
before putting the luminaire back into service.
• Electrically check to make sure that all connections are
clean and tight.
• Mechanically check that all parts are properly
assembled.
REPLACEMENT PARTS
Cooper Crouse-Hinds DMV Series Champ Luminaires are
designed to provide years of reliable lighting performance.
However, should the need for replacement parts arise, they
are available through your authorized Cooper Crouse-Hinds
distributor. Assistance may also be obtained through your
local Cooper Crouse-Hinds representative or the Cooper
Crouse-Hinds Sales Service Department, P.O. Box 4999,
Syracuse, New York 13221, Phone 315/477-7000.
©
2011, Cooper Industries, Inc.
WIRING DIAGRAMS
Mercury Vapor - 100, 175 and 250 watts all voltages.
Metal Halide (MH) - 175 and 250 watts all voltages.
High Pressure Sodium (HPS) - 50, 70, 100 and 150 watts
Metal Halide (MH) - 70 and 100 watts
120, 208, 240, 277 (MT) or 480 volts
High Pressure Sodium (HPS) - 50, 70, 100 and 150 watts
All statements, technical information and recommendations contained herein are based on information and tests we believe to be
reliable.The accuracy or completeness thereof are not guaranteed. In accordance with Crouse-Hinds "Terms and Conditions of Sale",
and since conditions of use are outside our control, the purchaser should determine the suitability of the product for his intended use
and assumes all risk and liability whatsoever in connection therewith.
Page 3
Rapid RestrIke Option - 70, 100, and 150 watts
HPS only
(Catalog Suffix IR)
120, 208, 240, 277 (MT)
all voltages
120V only
Cooper Industries Inc.
Crouse-Hinds Division
PO Box 4999, Syracuse, New York 13221 • U.S.A.
Copyright
©
2011, Cooper Industries, Inc.
IF 1083
Revision 6
Revised 03/11
Supercedes 03/09
Publicité
