Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
BS 400P
Always keep at a distance from the edges of building
pits and slopes. Avoid any operation that might be a
risk to machine stability! Keep the work area clean.
Cluttered areas and benches invite injuries! Do not
operate when you are tired! Watch what you are doing!
Risk of stumbling! Cables and hoses must complete
rolling up. After assembly do not leave any tools, a
wrench for example, on the unit.
Check to see that the tools are removed from the
machine before operating! Damaged blades have to
be changed immediately. Use only recommended
®
blades from the GÖLZ
Control the working area for water-, gas- and electrical
lines!
Important:
accomplished
prevents the appearance of particulate
matter and increases the life-time of the
diamond tool!
During work
Make sure, that the machine is well fastened before
and while cutting!
Never touch rotating parts like blade shaft or blade!
After work
Before leaving the machine always secure it against
unauthorized use!
3.6
Special work related to the main-
tenance and repair of the
machine
Observe the adjustment, maintenance and inspection
activities and intervals set out in the operating
instructions, including information on the replacement
of parts and equipment! These activities may be
executed by skilled personnel only.
Brief operating personnel before beginning special
operations or maintenance work, and appoint a person
to supervise the activities.
In any work concerning the operation, conversion or
adjustment of the machine and it's safety-oriented
devices or any work related to maintenance, inspection
and repair, always observe the start-up and shut-down
procedures described in the operating instructions and
the information on maintenance work. Ensure that the
maintenance area is adequately secured.
Carry out maintenance and repair work only of the
machine is positioned on stable and level ground and
has been secured against inadvertent movement and
buckling. If the machine is completely shut down for
maintenance and repair work, it must be secured
against inadvertent starting.
To avoid the risk of accidents, individual parts and
large assemblies being moved for replacement pur-
poses should be carefully attached to lifting tackle and
GmbH.
Wet
cutting
is
to
while
working!
secured. Use only suitable and technically perfect
lifting gear and suspension systems with adequate
lifting capacity. Never work or stand under suspended
loads.
The fastening of loads and the instructing of crane
operators should be entrusted to experienced persons
only. The marshaller giving the instructions must be
within sight or sound of the operator.
For carrying out overhead assembly work always use
specially designed or otherwise safety-oriented ladders
and working platforms. Never use machine parts as a
climbing aid. Wear safety harness when carrying out
maintenance work at greater heights.
Clean the machine, especially connections and
threaded unions, of any traces of oil, fuel or presser-
be
vatives before carrying out maintenance / repair. Never
This
use aggressive detergents. Use lint-free cleaning rags.
Before cleaning the machine with water, steam jet or
detergents, cover or tape up all openings which -for
safety and functional reasons - must be protected
against water, steam or detergent penetration.
Do not clean the machine with a high-pressure
cleaner. The hard water jet can put damage to parts of
the machine. After cleaning, remove all covers and
tapes applied for that purpose.
After
cleaning
connections, chafe marks and damage! Have identified
defects repaired immediately!
Always tighten any screwed connections that have
been loosened during maintenance and repair.
Any safety devices removed for set-up, maintenance
or repair purposes must be refitted and checked
immediately upon completion of the maintenance and
repair work. Ensure that all consumables and replaced
parts are disposed of safely and with minimum
environmental impact.
3.7
Information about special risks
with electrical energy
Observe the relevant national regulations or standards.
Electrical connections must always be kept free from
dirt and moisture.
Use only original fuses with the specified rating! Switch
off the machine immediately, if trouble occurs in the
electric power supply!
If your machine comes into contact with a live wire:
warn others against approaching and touching the
machine
have the live wire de-energized
When working with the machine, maintain a safe
distance from overhead electric lines. If work is to be
carried out close to overhead lines, the working
equipment must be kept well away from them.
Caution, danger to life!
Check out the prescribed safety distances.
Work on the electrical system or equipment may
only be carried out by a skilled electrician himself
- 23-
check
the
machine
®
for
loose
5009001-00
BA-D-E-F-FL
Publicité
Table des Matières
