Publicité

Les langues disponibles

Les langues disponibles

LuxaCrown
DMG Chemisch-Pharmazeutische Fabrik GmbH
Elbgaustraße 248 · 22547 Hamburg · Germany
www.dmg-dental.com
093034/#2_2018-09
EN
Instructions for use
FR
Instructions for use
Product description
LuxaCrown is a self-curing composite for the fabrication of semi-permanent crowns
and bridges that are cemented with a permanent or temporary luting cement. The
material is mixed automatically.
Indications
Crown restorations:
for restoration of the anatomical form in order to provide durable protection
for the remaining tooth;
in order to restore chewing function;
for esthetic corrections.
Bridge restorations:
in order to restore chewing function;
for esthetic corrections.
Contraindications
Do not use the material:
on preparations with a minimum wall thickness of < 1.5 mm;
on tooth cores with a height of < 3 mm;
in cases of allergies to any of the ingredients or, as can occur in rare cases, in
the event of contact allergies.
Side effects
There are no known systemic side effects to date.
Interactions
Leftover methacrylate-based materials may alter the setting behavior of the silico-
ne impression and bite registration materials.
▸ If a restoration was prepared beforehand, carefully clean the preparation and
the surrounding tissue with alcohol-soaked gauze and water spray before taking
the impression.
Basic safety information
For dental use only!
Keep out of the reach of children!
Avoid contact with the skin! In the event of accidental skin contact, immedia-
tely wash the affected area thoroughly with soap and water.
Avoid eye contact! In the event of accidental contact with the eyes, immedia-
tely rinse thoroughly with plenty of water and consult a physician if necessary.
Timing
0:00  –   0 :40 min*
1:45 –  2 :20 min
5:00 min*
*The indicated times apply at a room temperature of 23°C/73°F and a normal relative humidity
of 50%. Higher temperatures shorten, lower temperatures increase these times.
Recommended use
1. Before preparation of crowns or bridges, take an impression using alginate, sili-
cone or a thermoplastic impression material. Alternatively, the temporary can
be made using a laboratory-prepared thermoforming matrix. Strictly follow the
appropriate manufacturer's instructions.
Note: In a silicone impression, undercuts should be compensated for and, if neces-
sary, relief channels should be cut.
2. Dry the prepared teeth and compensate for any undercuts present in the pre-
paration.
3. Lightly coat the prepared teeth, surrounding tissue and any present composi-
te core build-ups with Vaseline or a similar separating agent.
Note: The convergence angle must be kept as small as possible in the preparation.
Ensure an appropriate connector cross-section with splinted crowns and bridges.
4. Select the desired LuxaCrown shade.
5. Fill the impression with LuxaCrown. Start by applying the material to the occlu-
sal surfaces and fill up working toward the gingival areas. Keep excess materi-
al to a minimum.
Note: To avoid bubbles, keep the mixing tip immersed in the material throughout
application.
6. After a maximum time period of 0:40 minutes from the start of mixing, place
the filled impression with moderate pressure on the prepared teeth and fix.
7. Monitor the setting process intraorally (e.g. with a probe), as the curing pro-
cess is influenced by the temperature in the mouth and as it is recommended
to take off the restoration during the elastic phase.
8. Remove the restoration from the mouth during the elastic phase, i.e. in the time
period from 1:45 to 2:20 minutes after the start of mixing.
9. Remove the oxygen inhibition layer at the surface of the restoration (e.g. with
alcohol).
Caution! Grinding dust can get in the eyes and airways when working on or
finishing the restoration.
▸ Wear a face mask and protective goggles.
▸ Make sure that grinding dust is properly extracted – do not breathe it in.
Mode d'emploi
ES
Instrucciones de uso
Place into the mouth
Remove from the mouth
Setting completed
Process restoration
English
1

Publicité

Table des Matières
loading

Sommaire des Matières pour DMG LuxaCrown

  • Page 1 Ensure an appropriate connector cross-section with splinted crowns and bridges. 4. Select the desired LuxaCrown shade. 5. Fill the impression with LuxaCrown. Start by applying the material to the occlu- sal surfaces and fill up working toward the gingival areas. Keep excess materi- al to a minimum.
  • Page 2 2. Attach a new mixing tip [E]. Note: In order to achieve an optimum mixing result, DMG recommends the use of the mixing tips available from DMG. All mixing tips are also available in refill packs. Note: Make sure that the notches on the mixing tip line up with those on the cartridge.
  • Page 3: Description Du Produit

    Prévoir une coupe transversale appropriée du connecteur pour les couronnes et bridges scindés. 4. Sélectionner la teinte LuxaCrown souhaitée. 5. Remplir l’empreinte de LuxaCrown. Commencer par appliquer le matériau sur les surfaces occlusales puis l’insérer dans les zones gingivales. Limiter au mini- mum l’excédent de matériau.
  • Page 4: Application Du Matériau

    2. Mettre en place une nouvelle canule de mélange [E]. Remarque : pour un résultat de mélange optimal, DMG recommande l’emploi de canules de mélange disponibles auprès de DMG. Toutes les canules de mélange sont également disponibles en écorecharges. Remarque : veiller à ce que les encoches de la canule de mélange et celles de la cartouche coïncident.
  • Page 5 4. Seleccione el tono deseado de LuxaCrown. 5. Rellene la impresión con LuxaCrown. Comience aplicando el material a las superficies oclusales y proceda al relleno moviéndose hacia las áreas gingiva- les. Mantenga el exceso de material al mínimo.
  • Page 6 2. Colocar la nueva cánula de mezcla [E]. Nota: para lograr una mezcla óptima, DMG recomienda el uso de las cánulas de mezcla suministradas por DMG. Todas las cánulas de mezcla están disponibles también en formato de envase de recarga.

Table des Matières