Publicité
Les langues disponibles
Les langues disponibles
Do not allow spool cap to drag on ground or other
surfaces.
In long growth, cut from the top down and do not exceed
300 mm high.
Keep trimmer tilted toward the area being cut; this is the
best cutting area.
The trimmer cuts when passing the unit from the left to
right. This will avoid throwing debris at the operator.
Avoid trees and shrubs. Tree bark, wood moldings, siding,
and fence posts can easily be damaged by the string.
Replacing the spool (Fig. N, O, P, Q)
Warning! To reduce the risk of serious personal injury, turn
unit off and disconnect it from power source before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury
Depress the tabs (15) and remove the spool cap (10a)
from the spool housing (16) in the trimmer head (Fig. N).
For best results, replace spool with BLACK+DECKER
model no. A6481.
Grasp empty spool with one hand and spool housing with
other hand and pull spool out.
If lever (17) (Fig. O) in base of housing becomes
dislodged, replace in correct position before inserting new
spool into housing.
Remove any dirt and grass from the spool and housing.
Unfasten the end of the cutting line and guide the line
into the eyelet (19) Fig. P.
Take the new spool and push it onto the boss ( 18 ) in the
housing (Fig. O). Rotate the spool slightly until it is
seated. The line should protrude approximately 136mm
from the housing.
Align the tabs on the spool cap with the slots (20) in the
housing (Fig. Q).
Push the cap onto the housing until it snaps securely into
place.
Warning! To avoid trimmer damage, if the cutting line
protrudes beyond the trimming blade, cut it off so that it just
reaches the blade.
Rewinding spool from bulk line (Fig. S, T)
Replacement spools of cutting line are available from your
BLACK+DECKER dealer. Packs containing 3
spools of cutting line are also available.
Unplug the tool.
Remove the empty spool from the trimmer as described
in "REPLACING THE SPOOL".
Remove any remaining cutting line from the spool.
Make a fold at the end of the cutting line at about 19mm
(21). Feed the cutting line into one of the line anchoring
slots (22) as shown in Fig. S.
Note: Take care not to allow the the line on the spool to
unravel. Hold it firmly with one hand at all times.
(Original instructions)
Insert the 19mm end of the bulk line into the hole (26) in
the spool adjacent to the slot as shown in Fig. S. Make
sure the line is pulled tight against the spool as shown in
Fig. T.
Wind the cutting line onto the spool in the direction of the
arrow on the spool. Make sure to wind the line on neatly
and in layers. Do not crisscross (Fig. T).
When the wound cutting line reaches the recesses (24),
cut the line. (Fig. S).
Fit the spool onto the trimmer as described in
"REPLACING THE SPOOL.
Warning! Before you begin trimming, only use the appropriate
type of cutting line.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in the new
plug.
Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Troubleshooting
If your tool seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
Warning! Before proceeding, unplug the tool.
Machine runs slowly
Check that the spool housing can rotate freely. Carefully
clean it if necessary.
Check that the cutting line does not protrude more than
approximately 136mm from the spool. If it does, cut it off
so that it just reaches the line trimming blade.
POWERCOMMAND feed does not work
Remove the spool cap.
Pull the cutting line until it protrudes approximately 136mm
from the spool. If insufficient cutting line is left on the
spool, install a new spool of cutting line.
Ensure that the line is not crisscrossed on the spool as
detailed in Fig. T. If it is, unwind the cutting line, then wind
it back on the spool neatly so that the lines do not cross.
Ensure the beginning of the cutting line is pulled tight
against the spool as shown in Fig. S.
Align the tabs on the spool cap with the cut outs in the
housing.
Push the spool cap onto the housing until it snaps
securely into place.
If the cutting line protrudes beyond the trimming blade, cut
it off so that it just reaches the blade.
ENGLISH
11
Publicité
