First Time Installation; Using Main Display Menu - Kimex 164-5070 Manuel D'utilisation

First Time Installation

When turned on for the first time, the language
selection screen will be displayed. Select the desired
language and press OK.
On the next screen, set your country preference and
press OK to continue.
You will be asked to set and confirm a PIN at this point.
For some country options, the PIN cannot be set to
0000, in this case you need to enter another 4-digit
number combination. You have to enter this PIN if you
are asked to enter a PIN for any menu operation later.
The Signage Settings menu will be displayed next.
Set ID, OSD Orientation, Auto Software Update
options can be configured using this menu. Model
name, Serial number and Software version options
are for information only. They will be grayed out and
not selectable. You can save the model information
data of the Display to a connected USB device using
the Save model information option. You can also
copy database files from a connected USB device to
the Display using the Clone from USB option. Also,
the NTP server option can be set here to get the
current time and date information over the network.
Refer to the Signage Menu Content section for
more information on the options of this menu. After
the settings are completed, highlight Next and press
OK to continue.
If the ERP Regulations 2021 are applied (depends
on the model of the unit): The following step will
be available
The Display Operation Mode selection screen will be
displayed next. For normal operation set the Power
Mode option to Reactive. Set to Eco for an energy-
efficient operation. In this mode your Display's settings
will be configured to reduce the energy consumption.
The Auto Launch Selection screen will be displayed
next. Vsign Lite, CMS, Open Browser and Disabled
options will be available. Highlight the desired option
and press OK to proceed.
On the next screen, the Network/Internet Settings
menu will be displayed. Please refer to Connectivity
section to configure a wired or a wireless connection.
If you want your Display to consume less power
in standby mode, you can disable the Networked
Standby Mode option by setting it as Off. After the
settings are completed highlight Next and press OK
button to continue.
The First Time Installation is completed.
To repeat this process and reset the Display's settings
to the factory defaults enter the Settings>Signage
menu, highlight First time installation and press
OK. You will be asked to enter the PIN that you have
defined in the First Time Installation. If the correct PIN
is entered a confirmation message will be displayed
asking whether you want to delete all settings and
reset the Display. Select Yes and press OK to confirm.
Note: Do not turn off the Display while initializing first time
installation. Note that, some options may not be available
depending on the country selection.

Using Main Display Menu

When the Menu button is pressed, the main Display
menu will appear at the bottom of the screen. You can
navigate through the menu items using the directional
buttons on the remote. To select an item or see the
sub-menu options of the highlighted menu press OK
button. When you highlight a menu option some of
the sub-menu items of this menu may appear on the
upper side of the menu bar for quick access. To use
a quick access item highlight it, press OK and set as
desired using the Left/Right directional buttons. When
finished press OK or Back/Return button to exit.
Press Exit button to close the main menu.
1. Home
When main menu is opened Home menu bar will
be highlighted. The content of the Home menu can
be customised by adding options from other menus.
Just highlight an option and press the Down direction
button on the remote. If you see Add to Home option
you can add it to the Home menu. Same way you
can delete or change the position of any item in the
Home menu. Press the Down direction button and
select Delete or Move option and press OK. In order
to move a menu item use the Right and Left direction
buttons to select the position that you want the item
to move to and press OK.
2. Settings
You can manage the settings of your Display using
the options of this menu. Refer to Settings Menu
Contents section for more information.
3. Apps
When your Display is connected to the Internet related
contents will also be available, including Apps related
contents. Using the Apps menu you can access
your applications. Refer to Apps section for more
information.
4. Sources
You can manage your input source references using
the options of this menu. To change the current source
highlight one of the options and press OK.
4.1. Source Settings
Edit the names, enable or disable selected source
options. There are also Regular, Enhanced and
Disabled options available for HDMI source. Regular
and Enhanced options are affecting the colour
settings of the HDMI source. To be able to watch 4K
or HDR/HLG images from the HDMI source its source
setting should be set as Enhanced if the connected
device is compatible with HDMI 2.0 and subsequent
English - 10 -