Kimex 164-5070 Manuel D'utilisation page 106

OPS Settings
(Optional)
Scheduler Settings
Link options
Volume Settings
Reset to Default
Values
Press OK to open the OPS Settings menu screen. Three sub-menu options are available.
OPS Information: Displays read-only information about the OPS unit, if supported.
OPS Status: Displays whether the OPS module is on or off. Allows the change of
status via soft PSON signal (0.5s)
Boot Signal: Enables or disables sending of a PSON signal. The Display checks the
status signal of the OPS at bootup in order to turn it on by sending a PSON signal if
it is off. Some OPS's send incorrect information on their status during the bootup of
the Display, so they seem to be on even though they are off. For such non-standard
OPS's, this option must be enabled. In this case, a PSON signal will be send for the
OPS regardless of the received status information at bootup.
Powerdown: Turns the OPS off via hard PSON signal (5s)
OPS Always on (optional): When this option is enabled, Quick Standby will be
forced to enabled and greyed out in the menu and OPS will not be set to standby (*).
(*) If the ERP Regulations 2021 are applied (depends on the model of the unit): When this option is
enabled, Power Mode will be forced to enabled (set to Reactive) and greyed out in the menu and OPS
will not be set to standby
Recovery Mode: When this option is enabled and OPS is on, if there is no video for 10
seconds it resets hotplug. If there is no video available after 30 seconds it reboots OPS.
Note: This menu will not be available if OPS is not supported or not connected to the unit.
Using the scheduler options you can set the unit to turn on automatically at defined time
intervals with the defined input source setting on the desired days of the week. Press OK
to open the Scheduler Settings menu screen. You can set up to 4 different schedulers.
Highlight the first checkbox of the desired scheduler option and check it by pressing
the OK button. Now you will be able to define a time for the Display to be turned on
automatically. Highlight the time box next to the first checkbox and press the OK button,
then use the directional and numeric buttons on the remote to set a time. Press the OK
button again when you are done.
Perform the same steps to set a time for the Display to turn off.
You can also define a source for your scheduler. Highlight the box located under the
Source tab for your scheduler option and press the OK button, then set as desired using
the Left/Right directional buttons. If the Source option is set as Last Source, the input
source will not be changed at the power-up. If the Source option is set as USB, the
media files in the connected USB device will be played back automatically as explained
in the section entitled 'USB Auto Play Feature'.
Lastly, you can select the week day/s for your scheduler setting to be activated. Highlight
the checkbox under the desired day tab and press OK to check. Highlight and press
OK a second time to uncheck a box. The scheduler will be active on the checked days
of the week.
You can also set a backlight scheduler. After setting the On, Off, Source and day options
highlight the checkbox under the Backlight column and press OK. The checkbox will
be checked and backlight level setting screen will be displayed. Set On value and
Off value using the sliders and then press OK to save. Mind that, in case you set a
backlight scheduler, the display will not be turned on or off, only the backlight values
will be changed at defined time interval. If Source option is set as Last Source the
backlight settings will be applied to all sources, otherwise the settings will be applied
to the selected source only.
Press the Green button on the main scheduler screen to save settings when complete.
Press OK to open the link options menu screen. Current Start url and Settings url links
will be displayed. These items are for information only and not selectable. Refer to Usage
of the Start URL section for information on setting the Start url. Open browser initial
page and NTP server link preferences can be configured using the related options.
Press OK to see available menu options.
Highlight this option and press the OK button on the remote to return the Display to
default settings.
English - 21 -