General Safety Rules - Skil 3410 Consignes De Fonctionnement/Sécurité

SM 2610028628 01-13 E_SM 2610028628 01-13 E.qxp 1/11/13 2:46 PM Page 2
"READ ALL INSTRUCTIONS" Failure to follow the safety rules listed below and other basic safety precautions
WARNING
may result in serious personal injury.
KEEP CHILDREN AWAY
Do not let visitors contact tool or extension cord. All visitors
should be kept away from work area.
KEEP WORK AREAS CLEAN
Cluttered areas and benches invite accidents.
MAKE WORKSHOP CHILD-PROOF
With padlocks, master switches.
AVOID DANGEROUS ENVIRONMENTS
Don't use power tools in damp or wet locations. Keep work
area well-lit. Do not expose power tools to rain. Do not use
tool in presence of flammable liquids or gases.
Electrical Safety
• Before plugging in the tool, be certain the outlet
voltage supplied is compatible with the voltage
marked on the nameplate within 10%. An outlet voltage
incompatible with that specified on the nameplate can
result in serious hazards and damage to the tool.
• Avoid body contact with grounded surfaces such as
pipes, radiators, ranges and refrigerators. There is an
increased risk of electric shock if your body is grounded.
• Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
• Do not abuse the cord. Never use the cord to carry
the tools or pull the plug from an outlet. Keep cord
away from heat, oil, sharp edges or moving parts.
Replace damaged cords immediately. Damaged cords
increase the risk of electric shock.
• When operating a power tool outside, use an outdoor
extension cord marked "W-A" or "W." These cords are
rated for outdoor use and reduce the risk of electric shock.
Personal Safety
KNOW YOUR POWER TOOL
Read and understand the owner's manual and labels affixed
to the tool. Learn its application and limitations as well as the
specific potential hazards peculiar to this tool.
DON'T OVERREACH
Keep proper footing and balance at all times.
STAY ALERT
Watch what you are doing. Use common sense. Do not op-
erate tool when you are tired. Do not operate while under
medication or while using alcohol or other drug.

General Safety Rules

Work Area
"SAVE THESE INSTRUCTIONS"
DRESS PROPERLY
Do not wear loose clothing or jewelry. They can be caught
in moving parts. Rubber gloves and non-skid footwear are
recommended when working outdoors. Wear protective hair
covering to contain long hair.
USE SAFETY GOGGLES
Also face or dust mask if cutting operation is dusty, and ear
plugs during extended periods of operation.
GUARD AGAINST ELECTRIC SHOCK
Prevent body contact with grounded surfaces. For example:
pipes, radiators, ranges, refrigerator enclosures.
DISCONNECT TOOL FROM POWER SOURCE
When not in use, before servicing, when changing blades,
bits, cutters, etc.
KEEP GUARDS IN PLACE
In working order, and in proper adjustment and alignment.
REMOVE ADJUSTING KEYS AND WRENCHES
When not in use, before servicing, when changing blades,
bits, cutters, etc.
AVOID ACCIDENTAL STARTING
Make sure the switch is in the "OFF" position before plugging
in tool.
NEVER STAND ON TOOL OR ITS STAND
Serious injury could occur if the tool is tipped or if the cutting
tool is accidentally contacted. Do not store materials on or
near the tool such that it is necessary to stand on the tool or
its stand to reach them.
CHECK DAMAGED PARTS
Before further use of the tool, a guard or other part that is
damaged should be carefully checked to ensure that it will
operate properly and perform its intended function. Check for
alignment of moving parts, mounting and any other condi-
tions that may affect its operation. A guard or other part that
is damaged should be properly replaced.
All repairs, electrical or mechanical, should
WARNING
be attempted only by trained repairmen.
Contact the nearest Skil Factory Service Center, Authorized
Service Station or other competent repair service.
Use only Skil replacement parts; any others
WARNING
may create a hazard.
Use only
WARNING
recommended by the manufacturer for
your model. Accessories that may be suitable for one tool
may become hazardous when used on another tool.
2.
accessories that are