Publicité
Les langues disponibles
Les langues disponibles
· When the control is switched- ON the ON/OFF-key
has priority over all other keys, so that the control can
be switched-OFF anytime, even in case of multiple or
continuous operation of keys.
· In the stand-by mode a continous operation will not be
signalized. However, before the electronic control can be
switched-ON again, it has to recognize that all keys are not
operated.
Key Lock
The actuation of the key lock key (9) in the wait or active
mode locks the keyboard and the assigned key-lock LED
(12) is statically illuminated. Here, the actuation times of
the key-lock key have to be taken into account. The control
continues to work in the set mode, but may no longer be
operated with any key, except the key-lock key (9) itself or
the on/off key (1).
The switching OFF with the on/off key (1) is also possible
in the locked condition. The assigned key-lock LED (12)
fades when switching off the control The key-lock function
included LED is active again when switching on (in wait
mode 10 s) until this is deactivated by a repeated actuation
of the key-lock key. The activation/deactivation of the key-
lock function in the off mode is not possible.
When programmed timers expire the respective timer
alarms may be confirmed by actuating any key without
needing to unlock the control.
The repeated actuation of the key-lock key in the wait or
active mode unlocks the keyboard and the assigned key-
lock LED fades. All sensor keys may be operated as usual
again.
Multi-circuit cut-off
Depending on the design it is possible to operate dual- or
triple-circuit radiant heating elements with the LITE-Touch
Control.
When a multi-circuit heating element is put into operation,
all heating circuits are switched-ON at the same time. If only
the inner heating circuits should be used, the outer heating
circuit can be switched-OFF by means of the multi-circuit
key or in individual steps.
By operating the multi-circuit key the respective outer
circuit of the assigned active cooking zone (setting π „0")
can be cutoff anytime. An activated outer circuit will be
indicated by an additional LED. A renewed operation of the
multi-circuit key will add the outer circuit(s) at any time, the
assigned LED´s glow again (toggle-function)
If a cooking zone other than the one with multi-circuit
function will be selected, the multicircuit status will be
changed and all cooking zones will be deselected (the
decimal point extinguishes).
Behaviour of dual-circuit cut-OFF:
If the heating element to be controlled is a triple-circuit
heating element, the course of action is as follows:
· The first activation of the multi-circuit key cuts-off the
outer heating circuit and the top LED extinguishes.
· A second activation of the multi-circuit-key cuts-off the
middle heating circuit. (also the bottom LED extinguishes.)
· A third activation adds the middle heating circuit again. A
further activation adds the third heating circuit as well and
the assigned LEDs glow again.
Audible signal (buzzer)
While the control is in operation the following activities will
be signaled by means of a buzzer:
· normal key activation with a short sound signal.
· continuous operation of keys over a longer period of time
(10 seconds ) with a longer, intermittent sound signal.
Timer function (optional)
The timer function is realized in two versions:
· Stand-alone timer 1..99 min: sound signal when the time
is over (= minute minder). This function is only available
when the cooktop is not in operation, i.e. when there is no
cooking.
· Cooking zone timer 1..99 min: sound signal when the
time is over, four cooking zones can be programmed
independently.
Timer as minute minder (stand-alone):
· If the control is OFF the standalone- timer can be operated
by activating the timer key. The timer display shows "00".
Operation of the Power-key puts the control back into the
stand-by mode and the stand-alone-timer will be cut-off.
· Adjustment range (0-99min), it can be set in 1-minute
steps with any key, starting at 1 up to 99 (end stop) with the
minus-key starting at 99 down to 0 (end stop)
· Continuous activation of the plusor minus-key results in a
dynamic increase of the adjustment speed up to maximum
value without sound signal.
· When the plus- or minus key is released in the meantime,
the adjustment speed starts again from a (low) initial value.
· Adjustment can be made with a continously activated
plus- or minus-key or by tip-operation (with sound signal)
After the timer is set the time runs down according to the
adjustment. When the time is over there is a sound signal
and the timer display blinks.
The sound signal will be stopped
· automatically after 2 minutes and/or
· by operating any key. Then the blinking of the timer display
stops and the display extinguishes.
Switching-OFF/changing the timer
· The timer can be changed or switched-off anytime by
operating the TIMER- or MINUS key (with sound signal).
The timer will be switched off by counting down to "0" with
the minus-key or by operating the TIMER- and MINUS-key
together, which sets the timer directly to "0". For 6 seconds
Publicité
