RAUMER Ring Safety 13 Manuel page 4

made and certified according to EN 12277 or EN 361, dynamic ropes certified according to
EN 892 or semi-static according to EN 1891, sling rings according to EN 566, lines
according to EN 354 , energy absorbers according to EN 355, etc...
The connector must be compatible to the device to which it is connected; if the
connection is incompatible, you can compromise the security features of the system
(release or break ...) .
Warning: Please avoid the use of these connectors with other devices made of different
materials. For example, don't use connectors made of stainless steel with galvanized steel
plates, because in a hostile environment there will be modest effects of galvanic
corrosion. Contact Raumer if you are not sure of the compatibility of your device.
OPERATION MODE
Opening and closure
Open the screw-motion gate and insert the connector in the anchor in the right position,
as shown in the attached technical data sheet.
The maximum aperture of the ring is 15 mm
Rotate the screw-motion gate until you close it completely.
Use only with closed and blocked screw-motion gate (danger of death if used incorrectly,
although with a partially open screw,motion gate); to lock the screw-motion gate, rotate it
and manually lock it. Be careful because frictions or vibrations may loosen or open the
screw-motion gate; regularly check the correct locking (for example, check that the
locking thread of the ring nut is not visible).
For the art. 534, in the upper area is welded obliquely, (but only into one side), a rod of 4
mm diameter. This bar creates the immovability of the carabiner from its place and then,
at the same time, it also prevents accidental tipping: the connector "working" well and
always with the right set - see the attached data sheet.
After a very frequent use the rope has unfortunately worn this carabiner (nothing is
forever!). With a large clamp you can then act on the rod (which is welded into only one
side...) and bend it enough, until you can remove the carabiner from its seat and replace it
with a new one by performing all the steps in the way reverse.
Precautions for use
Attention! The resistance of the device is greatly reduced if the screw-motion gate is
open. The carabiner provides maximum resistance if used in the sense of the length. Any
other stress reduces its strength. Also, do not apply loads on the locking screw of the
connector. Avoid items, obstacles or support points (descender, for example) that
interfere with carabiner and the screw-motion gate: they are very dangerous. The
Connectors of class Q should only be used where the user does not have to connect and
remove the connector frequently, that is to say many times during a working day. Each
point of support on the locking screw is dangerous;
Get used to always double the systems, especially the carabiners. During an abrupt
tension of the rope, the screw-motion gate can break, causing the opening of the
connector and the consequent exit out from the anchor of the rope or of the connected
device.
Use only if the outside temperature is between -40 ° and + 50°C because this can affect
the performance and safety of the product
ANCHORS
For safety reasons it is essential, for stop and fall systems, that the anchor point is always
positioned, if possible, above the user and must have a resistance in accordance with the
requirements of the EN 795 standard, ie greater than 12 KN ; the work is performed so as
to minimize potential falls and their height.
If the anchoring of the system is used for work at height it must comply with the
requirements of the standard EN 795.
For jobs that require frequent open and close of the connector it is preferable to use
models with automatic locking lever instead of manual locking.
If the anchor system is used for sports activities, you must observe the norms about those
activities and consult the instructions for use of the anchors
The position is essential for safely blocking a fall: carefully verify what will be the height of
Ring Safety 13 – Art. 533 – 534
the fall, length of rope and "pendulum" effect to avoid all possible obstacles (es. The
ground, rubbing against the rocks, etc.).
Also the length of the connector must be considered when used in a fall arrest system,
because influences the length of the same fall.
Always make sure that connectors inserted in their anchorage are free to move and to
position in the right direction of application of the load with perfectly closed screw-
motion gate.
COMPLEMENTARY STANDARDS INFORMATIONS
– provide for a rescue plan and define the means to act quickly in case of
difficulties (it means to be trained to apply the appropriate rescue
techniques).
– allow a sufficient height under the user so, in case of fall, do not collide with
obstacles (remember that also the length of the carabiner should be taken
into account when used in any fall arrest system, as it will influence the
lenght of a fall).
GENERAL INFORMATIONS
Life time
The potential life time of the Raumer's products is undefined (it is advisable to
replace them anyway after 10 years).
It is known that equipment may degrade progressively when it is used, so the actual
life time of the products can not be quantified precisely, but occurs when the
product becomes obsolete in the system or when it meets one of elimination.
The lifetime is also reduced considerably by the conditions and intensity of use:
heavy use, contact with chemicals substances, use near sea water or splashing
water (in this case we recommend the use our "Marine" anchors line, which are
more resistant to corrosion of salt), high temperatures, abrasions or cuts, damage
to parts/components of the product, chemical environments, mud, sand, snow, ice,
competence of the user, violent shocks , storage, are some of the factors that
accelerating product wear.
Warning: the duration may be limited to only one use in specific conditions (contact
with acids, dangerous chemicals products, if the product suffers sharp falls or
tensions, etc ... this list is not exhaustive). Remember that in a marine environment
or other potentially corrosive environments, it would be better to use materials
with high resistance to corrosion; despite this, the installer is invited to monitor and
inspect the connectors installed at regular intervals to check their status.
Resistence
Our products comply with the requirements of EN 362:2004 and EN 12275:2013 - see
attached technical data sheet.
Please note that the company Raumer disclaims any responsibility in case of improper
installation and/or use in inappropriate situations.
Our products also comply with the requirements of UIAA 121.
Elimination
Do not use the product:
– after a violent fall, since no visible deformations could be considerably
impaired resistance;
– if the result of the check is not satisfactory;
– when you do not know the entire history of its use and when it becomes
obsolete and you have the slightest doubt about its reliability;
when you can not close completely anymore the screw-motion gate
–
– when there's a play or exits off of the screw-motion gate
– when there's a general ware of the body and/or a considerable decrease of
the section of the throat.
if there're cracks, wear or defects;
–
– when corrosion severely alters the surface condition.
Destroy retired equipment to prevent further use.
Product obsolescence
The product may be judged obsolete and thus retired from service, when they occur, for
example, incompatibility with other equipment, changes in applicable standards, etc ...
Chemical products
All chemicals, solvents or corrosive substances can be very dangerous for these items. If
there's a chance to come in contact with these substances contact directly Raumer
indicating composition and exact name of the product, so we can respond properly after
studying the case.
Changes and repairs
Modifications and/or repairs not authorized by the company Raumer are prohibited
because they can reduce product performance. Repairs or modifications must be carried
out inside the department production of Raumer Srl and not outside.
Warranty
This product has a 3-year warranty, against every defects in manufacturing or material.
The guarantee excludes oxidation, normal wear and tear, modifications or alterations,
incorrect storage, damage due to accidents, incorrect storage, negligence and improper
use.
Transport
It does not need any special precautions for transportation, however avoid contact with
chemical reagents or other corrosive substances and adequately protect from any pointed
objects or sharp.
Attention: never leave your equipment in cars parked in the sun!
Maintenance and storage
The user should not perform any special maintenance, but should be limited to the
cleaning of the product as explained below.
Cleaning: frequently rinse the product only with lukewarm fresh water (max 40°C). Leave
it to dry naturally away from direct heat.
Lubrification: frequently lubrificate all the moving parts with silicone based oil.
Avoid the contact of the oil with any textiles parts. Do this operation after cleaning and
the complete drying of the connector.
Storage: after cleaning and drying, store the equipments in a dry, cool, dark place (avoid
UV rays), chemically neutral place (absolutely avoid saline environments), away from
sharp edges, heat, humidity, corrosive substances or other potentially harmful conditions.
Caution: Do not store when wet! Improper storage, as well as the aging of the product,
may damage it and impair its performance and safety.
Testing and conformity
This product is a PPE of III category and is certified in accordance with EN 12275:
2013 and EN 362: 2004 and with Regulation (EU) 2016/425 of the European
Parliament and of the European Union Council, carried out by the notified body
n°2008 - DOLOMITICERT S.C.A.R.L., ZI Villanova 7/A - 32013 Longarone (BL).
In this regard, see the product marking and the EC declaration of conformity.
This product is also UIAA 121 tested and certified: Quality Label of the International
Union of Mountaineering Associations.
In this regard, see the product marking and the EC declaration of conformity.
product is also tested and complies UIAA 121: Quality Label of the International Climbing
and Mountaineering Federation. Attention: laboratory tests, the instructions for use and
standards are not always able to reproduce the practice, so the results obtained in real
conditions of use in natural environments may sometimes differ to a considerable degree.
The best instructions can be had from continuous use under the supervision of qualified
and prepared instructors.
This
2021