Assembly; Safety Information - EINHELL PS 13 Niro UKS Mode D'emploi

Anleitung PS 13 Niro UKS_SPK7:_
Item 9 Foot console
Item 10 Pan head screw M6x12
Item 12 Hex screw M6x12 mm, galvanized
Item 15 Hex nut M6, galvanized
Item 18 Washer, 6.4 mm, galvanized
Item 20 Washer, 8.4 mm
Item 21 Allen screw M8x30 galvanized
Item 22 Rubber bush
Item 23 Wheel
Item 24 Stop nut M8 galvanized
Item 29 Toggle switch

5. Assembly

5.1 Information
a) You will need the following additional tools for the
installation:
1 Screw wrench 10 mm, 13 mm
1 Allen key 6 mm
1 Phillips screwdriver
b) Do not tighten the screw connections until all the
individual parts have been fully assembled.
5.2 Assembly procedure
Notes
The item numbers in the text refer to the item
numbers in section 4.
Remove the protective foil before assembly. Use
a knife to carefully cut the foil where the cover
and case meet and remove the foil.
1. Place the holders (7) on the foot (8) and secure
them firmly with 6 x hex screws (12), washers
(18) and three hex nuts (15). (Detail in Fig. A)
2. Place the column (4) in the washer (5), push the
rubber bush (22) over it and secure it with 3 x
pan head screws (10), washers (18) and 3 x hex
nuts (15). (Detail in Fig. B)
3. Fit the wheels (23) to the foot base (9) with two
Allen screws (21), two washers (20) and stop nuts
(24) (Detail Fig. G).
4. Screw the foot base (9) to the foot (8) with two
hex screws (12), corresponding washers (18) and
two hexagon nuts (15) (Detail Fig. F)
25.01.2007 9:14 Uhr
1
5. Place the assembled washer (5) and column (4)
3
on the holders (7), fit the washer with 6 hex
20
screws (12), washers (18) and 6 hex nuts (15).
17
(Detail Fig. C)
23
2 6. Slide the case with cover (6) over the column (4)
2
and over the rubber bush (22).
1
2 7. Feed the hose through the column (4) and
2 secure the complete burner to the top of the
column (4) using 3 x hex screws (12) and the
1
corresponding washers (18). (Detail in Fig. D)
8. Secure the reflector (1) to the burner (2) with 3 x
hex Allen screws (12) and corresponding
washers (18). (Detail in Fig. E)
9. Connect to gas cylinder as described in section
7.

6. Safety information

The device must be installed and the liquid gas
cylinder stored in accordance with the current
regulations.
Do not move the device when it is operating.
Before moving the device, close the valve on the
liquid gas cylinder or the pressure regulator.
The hose lines must be replaced within the
specified periods.
Use only the gas types and liquid gas cylinders
specified by the manufacturer.
Special care must be taken in strong wind to
ensure that the device does not fall over.
6.1 Additional safety information
The liquid gas cylinder is to be changed in a well
ventilated area away from naked flames
(candles, cigarettes or other devices with a
naked flame, etc.)
Check that the seal on the pressure regulator is
fitted correctly and that it can perform its function.
Do not cover the ventilation openings in the
setting chamber for the liquid gas cylinder
Close the valve on the liquid gas cylinder or the
pressure regulator after use.
Do not use the device if gas is leaking or, if it is
already in use, the gas supply must be shut off
and the device must be inspected and repaired
Seite 11
GB
11