YAKINIKU Shichirin Instructions page 29

Attach the support to the connector with one M6 Screw
Step 1
and Acorn Nut by hand. Refer to picture of Step 1.
Attach the support to the connector with one M6 Screw
STEP 1
ep 1
and Acorn Nut by hand. Refer to picture of Step 1.
Attach the support to the connector with one M6 Screw
Step 1
Attach the support to the connector with one M6 Screw
and Acorn Nut by hand. Refer to picture of Step 1.
Step 1
and Acorn Nut by hand. Refer to picture of Step 1.
Attach the support to the connector with one M6 Screw Attach the support to the connector with one M6 Screw
1 Step 1
and Acorn Nut by hand. Refer to picture of Step 1. and Acorn Nut by hand. Refer to picture of Step 1.
Repeat Step 1.
Step 2
ld
Refer to picture of Step 2.
Repeat Step 1.
ep 2
Refer to picture of Step 2.
Repeat Step 1.
Repeat Step 1.
Step 2
Step 2
ld
STEP 2 Refer to picture of Step 2.
Refer to picture of Step 2.
Repeat Step 1. Repeat Step 1.
2 Step 2
d
Refer to picture of Step 2. Refer to picture of Step 2.
Attach the band to the bottom support with two M6 screws and
Step 3
Attach the band to the bottom support with two M6 screws and
ep 3 acorn nuts by hand. Refer to picture of Step 3.
ews
acorn nuts by hand. Refer to picture of Step 3.
Attach the band to the bottom support with two M6 screws and
Step 3
Attach the band to the bottom support with two M6 screws and
Step 3
acorn nuts by hand. Refer to picture of Step 3.
acorn nuts by hand. Refer to picture of Step 3.
ews
Attach the band to the bottom support with two M6 screws and Attach the band to the bottom support with two M6 screws and
3 Step 3
STEP 3
acorn nuts by hand. Refer to picture of Step 3. acorn nuts by hand. Refer to picture of Step 3.
ews
2
2
2
2
EN
Step 4
Repeat Step 3.
STEP 4
Step 4
Refer to picture of Step 4.
Repeat Step 3.
Step 4
Step 4
Refer to picture of Step 4.
Repeat Step 3.
Step 4 Step 4
Refer to picture of Step 4.
Step 5
Attached the bamboo handles to the bands with eight screws
Step 5
by screwdriver and tightened. The handle's Logo facing up.
Refer to picture of Step 5. Attached the bamboo handles to the bands with eight screws
Step 5
Step 5
by screwdriver and tightened. The handle's Logo facing up.
STEP 5
Refer to picture of Step 5.
Attached the bamboo handles to the bands with eight screws
Step 5 Step 5
by screwdriver and tightened. The handle's Logo facing up.
Refer to picture of Step 5.
Step 6
Tighten all screws by wrench. Then put the metal heat shield
Step 6
on the stand.
Tighten all screws by wrench. Then put the metal heat shield
Step 6
Step 6
on the stand.
Tighten all screws by wrench. Then put the metal heat shield
Step 6 Step 6
STEP 6
on the stand.
3
3
3
3
3 3
29
Repeat Step 3.
Refer to picture of Step 4.
Repeat Step 3.
Refer to picture of Step 4.
Repeat Step 3.
Refer to picture of Step 4.
Attached the bamboo handles to the bands with eight scre
by screwdriver and tightened. The handle's Logo facing u
Refer to picture of Step 5.
Attached the bamboo handles to the bands with eight scr
by screwdriver and tightened. The handle's Logo facing u
Refer to picture of Step 5.
Attached the bamboo handles to the bands with eight scre
by screwdriver and tightened. The handle's Logo facing up
Refer to picture of Step 5.
Tighten all screws by wrench. Then put the metal heat sh
on the stand.
Tighten all screws by wrench. Then put the metal heat sh
on the stand.
Tighten all screws by wrench. Then put the metal heat sh
on the stand.