Adjusting The Amount Of Frothed Milk; Restoring Preset Quantities; Latte Macchiato - Tchibo Saeco Cafissimo HD8603 Mode D'emploi

6- The Frothed milk button
7- When it has finished warming up, the machine dispenses the
frothed milk directly into the glass. The machine will stop dis-
pensing when it reaches the preset quantity. The dispensing
process can be stopped early by pressing the Frothed milk but-
ton .
When the machine has finished preparing the frothed
milk, the rinse button
that the milk circuit must be rinsed; see the section ''Rinsing
the milk circuit'' in this chapter.

Adjusting the amount of frothed milk

The machine allows you to adjust the amount of frothed milk
prepared according to your taste and the size of your glass.
Before preparing the frothed milk, check that the
On/Off button
stantly lit and that there is enough water in the tank.
Proceed as follows to set the desired quantity of Frothed milk :
1- Insert the carafe into the machine and ensure that the milk is
above the MIN level.
2- Place a glass underneath the milk dispensing spout as indicated
in the section "Adjusting the dispensing height".
3- Press and hold the Frothed milk button
flashes in brief intervals. Then release the button.
4- Press the Frothed milk button
milk in the glass reaches the desired level.
At this point the Frothed milk button
Each time it is pressed, the machine will prepare the same amount
of frothed milk that was just programmed.
Minimum quantity of milk that can be set: approx. 50ml
Maximum quantity of milk that can be set: approx. 300ml
Preset quantities:
Frothed milk: approx. 110ml
Restoring the pre-set quantities
To reset beverages to their factory settings, with the machine off,
press and hold the On/Off
for 5 seconds. All the buttons will flash twice in confirmation.
flashes; the machine is warming up.
will light up to remind you
and beverage buttons are con-
for 3 seconds until it
again when the amount of
has been reprogrammed.
and Filter coffee (blue) buttons

Latte macchiato

Before dispensing the latte macchiato, check that the
On/Off button
stantly lit and that there is enough water in the tank.
We recommend approx. 130ml frothed milk and 40ml espresso
for a latte macchiato. If necessary, you can reset the quantity
of milk as described in the section "Adjusting the amount of
frothed milk" before preparing the beverage.
1- Insert the carafe in the machine and ensure that the milk is
above the MIN level.
2- Adjust the machine to fit the glass into which your latte mac-
chiato will be dispensed (see section ''Adjusting the dispensing
height'').
3- Place a glass under the coffee and milk
dispensing spouts.
4- DO NOT insert a coffee capsule into the
capsule compartment.
5- Press the Frothed milk button .
6- The Frothed milk button
the machine is warming up.
7- When it has finished warming up, the
machine dispenses the frothed milk directly into the glass. The
machine will stop dispensing when it reaches the preset quan-
tity. The dispensing process can be stopped early by pressing the
Frothed milk button .
Make sure there is enough space in the glass for the
coffee when dispensing the milk.
Fig.1
8- Lift the capsule compartment opening lever (Fig.1).
9- Insert the capsule as shown in the figure (Fig.2).
10- Lower the lever to close the capsule compartment (Fig.3).
11- Press the (white) button for an espresso, the
button for a caffè crema or the
coffee.
12- Coffee brewing stops automatically when the set level is
reached. However, it is possible to stop the dispensing process
early by pressing the same button as the beverage being dis-
pensed.
and beverage buttons are con-
flashes;
Fig.2 Fig.3
(yellow)
(blue) button for a filter
• 25 •