Removal Of Package; Machine Parts' Description (Fig. 2-3); Adjustments; Adjustment Of Cutting Angle - Head Rotation (Fig. 2) - Fox F36-090 Notice D'utilisation

The sources of the noise of the saw are: the electric engine
and its ventilation system, the speed reduction device, the
blade and the material to be cut.
We advise you to control the engine, its ventilation system
and the aspiration passages. As far as the saw blade is
concerned, it is preferable to use silenced type of blades
and to keep them in good conditions. We recommend to
use the correct saw blade and to keep fi rmly the workpieces
to be cut.
Noise levels are emission levels and do not necessarily
indicate safe working conditions. Even if there is a
connection between emission levels and exposure levels,
the fi rst ones cannot be used to determine safely if other
precautions are necessary. The factors that can infl uence
the actual exposure level of the operator include the
exposure length, environmental features and other sources
of noise, as for example the number of machines and
operations in the surrounding area. Besides, exposure
levels can change from country to country. However,
these instructions enable the user of the machine to better
evaluate the dangers and risks.

REMOVAL OF PACKAGE

The parts included in the package are:
– Mitre saw
– Wrenches for replacing the blade
– 5 mm Allen wrench
– Additional lower protection
– Pusher
– Mitre gauge included in the fence
– Vertical clamp
– Dust collection sack
– Workbench extension
– Bar stop rod
Remove the mitre saw and all the parts from the package,
check if there are any missing or damaged parts.
In case there are any faulty or damaged parts do not use
them in order not to compromise the effi ciency and the
safety of the machine. To change faulty parts consult an
after sales centre.
In order that the mitre saw perfectly works, you must
assemble the various parts, for which you can fi nd a
detailed explanation later on.
MACHINE PARTS' DESCRIPTION
(Fig. 2-3)
1. Control handgrip
2. Main switch button
3. Base
4. Body/base swivel joint
5. Rotating support
6. Motor
7. Blade
8. Swivel locking knob
9. Head release button
10. Moving protective cap
11. Moving protective cap
16
12. Upper workbench
13. Upper moving protective cap
14. Bearing bracket
15. Bearing feet
16. Locking pin
17. Pointer
18. Fence
19. Main switch locking device
20 Workbench extensions
28 Vertical clamp

ADJUSTMENTS

WARNING!
Be sure that the mitre saw is switched off and
disconnected from any current source before
any adjustment, maintenance or cleaning work
and before changing the blade.
After carrying out all the adjustments, ensure
that all wrenches and tools are away from the
machine, and that all screws, bolts and other
locking devices are correctly blocked.
Do not use the mitre saw before following these
procedures.
While carrying out these adjustments, check that
all parts of the machine correctly work and are in
good conditions.
Any damage or broken part must be replaced by
a skilled person before use.
ADJUSTMENT OF CUTTING ANGLE - HEAD
ROTATION (Fig. 2)
This mitre-saw can cut both to the left and to the right.
The pre-set positions are every 5° both on the left and on
the right.
To place the machine this way, loosen the knob 8, release
the machine head and rotate the swivel support by using the
handgrip 1, then lock it by tightening the knob 8.
The head will automatically stop each time the index 17 is
in alignment with the corresponding position indicated on
the graduated plate.
For all intermediate positions, once the index 17 is aligned
with the position on the plate, block the rotating bearing
using the knob 8.
ADJUSTMENT OF CUTTING ANGLE - HEAD
ANGLE (Fig. 4)
The machine head can be tilted to a maximum of 45° to
the left.
Raise the upper surface to its maximum height, release the
handwheel 21 at the rear of the machine and tilt the head
until it comes into contact with the stop at 45°.
Retighten the handwheel 21.
WARNING: Ensure the knob 24 locks the head in
any position throughout every operation.