Publicité
Les langues disponibles
Les langues disponibles
GROUNDING
Improperly connecting the ground-
WARNING
ing wire can result in the risk of
electric shock. Check with a qualified electrician
if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug pro-
vided with the tool. Never remove the grounding
prong from the plug. Do not use the tool if the
cord or plug is damaged. If damaged, have it
repaired by a MILWAUKEE service facility before
use. If the plug will not fit the outlet, have a
proper outlet installed by a qualified electrician.
Grounded Tools (Three-Prong Plugs)
Tools marked "Grounding Required" have a three
wire cord and three prong grounding plug. The plug
must be connected to a properly grounded outlet
(See Figure A). If the tool should electrically mal-
function or break down, grounding provides a low
resistance path to carry electricity away from the
user, reducing the risk of electric shock.
The grounding prong in the plug is connected through
the green wire inside the cord to the grounding
system in the tool. The green wire in the cord must
be the only wire connected to the tool's grounding
system and must never be attached to an electrically
"live" terminal.
Your tool must be plugged into an appro-
priate outlet, properly installed and
grounded in accordance with all codes
and ordinances. The plug and outlet
should look like those in Figure A.
Double Insulated Tools (Two-Prong Plugs)
Tools marked "Double Insulated" do not require
grounding. They have a special double insulation
system which satisfies OSHA requirements and
complies with the applicable standards
of Underwriters Laboratories, Inc., the
Canadian Standard Association and
the National Electrical Code. Double
Insulated tools may be used in either
of the 120 volt outlets shown in Figures
B and C.
ASSEMBLY
To reduce the risk of injury, always
WARNING
unplug tool before changing or
removing accessories. Only use accessories
specifically recommended for this tool. Others
may be hazardous.
Always use a side handle when using this tool.
Always brace or hold securely.
Adjusting the Side Handle Position
1. Loosen the side handle by unscrewing the side
handle grip until the side handle rotates freely.
2. Rotate the side handle to the desired position.
3. Tighten the side handle grip securely.
1. Press in the clamping lever.
2. Slide the depth gauge rod backward
or forward until it is set for the de-
sired depth.
NOTE: The drilling depth is the
distance between the tip of the bit
and the tip of the depth gauge rod.
3. Release the clamping lever.
WARNING
the bit while the chuck is rotating
or while the bit is falling from the
chuck.
NOTE: Only use accessories with SDS or SDS Plus
shanks.
Be sure that the shank of the bit is clean. Dirt particles
may cause the bit to line up improperly. Do not use
bits larger than the maximum recommended capacity
of the drill because gear damage or motor overload-
ing may result. For best performance, be sure that
the bit is properly sharpened and the shank is lightly
greased before use. Use caution when handling hot
bits and chisels.
1. Unplug tool.
2. Insert the bit or chisel into the nose of the tool.
3. Push bit into tool until it locks.
4. Check to see that the bit is locked by tugging on it.
5. To remove bits and chisels, pull back on the bit
release collar and remove bit.
Fig. A
WARNING
removing accessories or making adjustments.
Use only specifically recommended accessories.
Others may be hazardous.
Always wear proper eye protection marked to
comply with ANSI Z87.1.
When working in dusty situations, wear appro-
Fig. B Fig. C
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Keep hands and cord away from the bit and all
moving parts.
Always use a side handle when using this tool.
Always brace or hold securely.
Cut embedded rebar only if this operation does
not affect the integrity of the building. If in doubt,
consult a structural engineer. Tool operator fully
responsible for adverse structural effects.
MILWAUKEE Rotary Hammers have three settings:
rotation only, rotary hammer, and hammer only.
Always allow the motor to come to a complete stop
before changing the mode selection to avoid dam-
age to the tool.
1. For rotation only, turn the
selector lever so the arrow
on the lever points to the
twist drill symbol.
2. For rotary hammering, turn
the selector lever so the ar-
row points to the hammer
and twist drill
3. For hammering only, turn
the selector lever so the arrow points to the ham-
mer symbol.
4
Setting the Depth Gauge
To reduce the risk of
injury, do not grasp
Installing Bits and Chisels
OPERATION
To reduce the risk of injury, always
unplug tool before attaching or
Selecting Action
symbol.
Drilling
Depth
Publicité
