Cardin ZVL548.00 Mode D'emploi page 18

Transmitters
The transmitter is pre-coded and is fitted with an integrated circuit which is programmed in the factory with a
unique identification number. All the code parameters are contained in this integrated circuit (external memory
modules are not required) thus making code management more reliable and the system more secure. The
transmitter has an automatic shut down mechanism which cuts in after at least 20 seconds of continuous use
(this limits battery consumption).
Key block function
• A key block function has been added to protect the appliance from accidental activation;
- to activate the function press and hold down "MR" for 8 seconds until the red led starts
flashing, at this point to activate a command you will need to press the required key
three times consecutively;
- to reset the function to standard operation standard press and hold down "MR" for 8 seconds until the red
led starts flashing.
Receiver
Warning! The receivers must only be powered by a safety power pack. The use of non safety power packs
could provoke damage to the system.
Outdoor receiver with LCD display IP55 (fig. 1)
- The outdoor receiver (printed circuit CS1444AB) is fitted with an 20-way terminal board and has a 12-24Vac-
dc electrical connections between binding posts 1-2.
For the installation of the outdoor receiver see the separate instructions for mounting the box (ZVL105.02).
Note: Using the antenna extension cable will reduce the protection grade level to IP40.
Interchangeable channel modules
The receiver can be fitted with up to four MCCMORPHM0 interchangeable channel modules which can set
via software (see setting the relays).
Status inputs
The receiver is fitted with four independent inputs, IN1...4 , which can be used to monitor the status of the
external devices. You can obtain the status of the inputs either by sending and receiving an SMS or through
the gateway. The 'IN' contacts 1 to 4 can either be wired to a potential free contact or connected to a signal
whose direct current voltage can vary from 0 to 18V; in this case for voltages less than 1.8V the contact is
deemed to be closed and for voltages greater than 1.8V it is deemed to be open. The status of each input,
along with its individual identification number, is shown in real time on the receiver's display. If for example
number '1' appears on the display, this means that the input is 'high' or 'open' while if a hyphen '-' appears on
the display the input is 'low' or 'closed'.
The status inputs have a particular function, based on the Gateway Cardin service, which will notify you when an
input has taken on a certain status for a fixed amount of time. The threshold for the indication and the response
time can be set independently for each input using the software CardinTX_SW. For more information about
this function consult the instructions for the CardinTX_SW software.
Serial number
Each receiver has its own individual serial number which allows it to access the data exchange gateway. The
serial number cannot be modified . The receiver's serial number is marked on a label on the printed circuit
board (see fig. 1). If for some reason the label has been removed the serial number can be read on the display
by scrolling down to menu number 10 and then pressing
appear on the display.
Receiver connectivity
Connection to the receiver in order to manage user data can take place in three different ways:
• Hardware hook up: using a usb cable fitted with a "USB MINI" connector
• 2G Mobile network: using a modem connected to the computer fitted with the necessary software.
• 3G Mobile network: using the gateway service supplied by Cardin Elettronica (only for Cardin products)
which allows the receiver to be directly accessed through internet.
For details regarding the setup and use of these processes consult the instructions supplied with the software.
. The product identification number will
ENT
18
Description : MEMORIZZAZIONE CODICE TX-RX
Drawing number :
DM0531
Product Code : RCQ449100
Draft : P.J.Heath Date : 13-04-2001
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831