Skil 7710 Notice Originale page 9

• Speed control 7
- select working speed by sliding switch A into desired
position
1 = low speed for precision work
2 = medium speed
3 = high speed for quick removal of material
- the optimal working speed depends on the material
and can be determined with practical trials
• Operating the tool
! wear protective gloves and use safety glasses
- mount desired accessory
- switch on the tool
- advance the tool to the material/location to be scraped
- start with a flat angle and light pressure
- work away from the body
- be aware that the stroke motion of the tool is only
produced when pressure is applied to the material to
be removed
- be aware that too much pressure may cause damage
to the background material
! do not overload the tool
! allow tool and accessory to cool down between
the individual work steps
• Sharpening of accessories
- with sharp accessories, good working performance
and a long service life can be achieved
- sharpen the steel accessories before they come dull
APPLICATION ADVICE
• Use accessory G for working on hard materials 8
! soft materials (such as wood and aluminium) can
be easily damaged with extra sharp blades
Possible applications are:
- removal of carpet adhesive and foam-, plaster-,
mortar- remains as well as remains of joint material
- smoothing of unevennesses
- removal of floor coverings
! hold the tool firmly with both hands and take a
secure stance
• Use accessory H for working on soft materials 9
Possible applications are:
- removal of paint residue, silicon and plaster as well as
stucco from glass and plastic panels
- smoothing and removing of adhesive and sealing
residues from wooden flooring
• Use accessory J for carving work 0
- carving is possible only in wood with short fibres (such
as linden and poplar)
! hold the tool firmly with both hands and take a
secure stance
• Use accessory K for removing sealing from window joints
or remains from door rabets !
mAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots F 2)
- clean the tool with a dry, soft cloth (do not use cleaning
agents or solvents)
! disconnect the plug before cleaning
• Keep tool as well as accessories free from adhesives or
any other residuary material
• Always store the tool indoors in its protective carton/case
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
ENVIRONmENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 5 will remind you of this when the need for
disposing occurs
NOISE / VIBRATION
• Measured in accordance with EN 62841 the sound
pressure level of this tool is 81 dB(A) and the sound
power level 92 dB(A) (standard deviation: 3 dB), and the
vibration 12.7 m/s² (triax vector sum; uncertainty
K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 62841; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Grattoir
INTRODUCTION
• Cet outil est conçu pour ôter/gratter les éléments
détritiques des revêtements ainsi que les résidus de
colles et de matériaux de remplissage, pour lisser les
irrégularités et pour des travaux de creusement dans du
bois tendre
• Cet outil n'est conçu pour un usage professionnel
• Lisez et conservez ce manuel d'instruction 3
9
7710