Gorenje CB8900E Guide Rapide page 3

Use of the Oven
Setting the time on the clock
On connecting the oven, you will notice that
12:00 appears on the clock and that a light
begins to flash above the symbol. Pressing
the "+" and "-" buttons the correct time can be
set on the clock, which is subsequently stored
and the flashing light goes out.
Manual use
After setting the correct time, the oven is ready
for use. Select a temperature and a cooking
function.
To switch off the oven, set the controls to the
position .
Functions of the Electronic Clock Programmer
Warning function: This function generates a
warning tone at a specified time.
Cooking time: This function allows to
programme the oven to cook for a specified
time, after which it will switch itself off.
End of cooking time: This function allows to
establish the exact hour, after which the oven
will switch itself off.
Duration and automatic stop: This function is
used to control the duration and the time at
which the oven will turn itself off. This function
allows the oven to star t and
automatically.
Clock light: The clock light can be switched off
when the oven is not in use.
Warning function
1 Press the MODE button until the signal
above the symbol begins to flash.
2 Choose the time when you want the alarm
to sound, pressing the "+" or "-" buttons.
3 Subsequently, the light will remain on
indicating that the alarm is programmed.
4 At the end of the programmed time, an
alarm will sound and the light will begin to
flash.
5 Press any button to turn off the alarm and
the screen shows the current time again.
4
Programming the cooking time
1 Press the MODE button until the indicator
above the symbol begins to flash.
2 Select the length of time, pressing the "+"
or "-" buttons.
3 Subsequently, the indicator that was
flashing will light, indicating that the oven
will switch itself off automatically.
4 The clock will then show the current time.
5 Select a temperature and cooking function.
6 When the set time has elapsed, the oven
will disconnect, an alarm will sound and the
indicator will begin to flash.
7 Press any button to switch off the alarm,
reconnecting the oven.
8 Set the controls in the position
off the oven.
Programming the end of cooking time for the oven
1 Press the MODE button until the indicator
above the symbol begins to flash.
2 Select the time that cooking is to finish,
pressing the "+" or "-" buttons.
3 Subsequently, the indicator that was
flashing is lit, indicating that the oven will
switch itself off automatically.
stop
4 The clock will then show the current time.
5 Select a temperature and a cooking function.
6 When the programmed time is reached, the
oven will disconnect, an alarm will sound
and the indicator will begin to flash.
7 Press any button to switch off the alarm and
the oven will reconnect.
8 Set the controls to the position
off the oven.
This function may be used even though you are
already cooking in your oven. To do so, follow
the instructions given except Nº 5.
Programming the duration and automatic
stop
1 Press the MODE button until the indicator
above the symbol begins to flash.
2 Select the length of cooking time pressing
the "+" or "-" buttons.
3 Subsequently, the indicator that was
flashing will remain lit.
4 Press the mode button until the indicator
above the symbol begins to flash.
5 Select the time that cooking should finish
pressing the "+" or "-" buttons.
6 Subsequently, the indicator that was
flashing will remain lit.
7 Select a function and cooking temperature.
8 The oven will remain disconnected with the
indicators above the
Your oven is programmed.
9 When the time to begin cooking is reached,
the oven will switch itself on and will
continue cooking during the programmed
time.
to switch
10 When the programmed finishing time is
reached, the oven will disconnect, an alarm
will sound and the light above the
symbol will begin to flash.
11 Press any button to switch off the alarm
and the oven will reconnect.
12 Set the controls to the position
switch of the oven.
Caution
Pressing the MODE button the display on the
screen shows any function programmed. It can
be changed by pressing the "+" or "-" buttons.
to switch
On selecting the desired function, the
indicator above the corresponding signal will
light.
In the event of a power cut, all the
programming of the electronic clock will be
erased. The correct time has to be reset and
the watch reprogrammed.
Switching off the clock light
To switch off the clock light, press two buttons
at the same time and, after several seconds
the screen of your clock will go out. To re-light
the clock, press any button and the current
time will reappear.
and symbols lit.
This function can only be used when the clock
shows the current time and there is no function
programmed (No function symbol is lit).
to
5