Sleep Mode - BH HIPOWER SK LINE sportkoncept R250 Instructions De Montage Et Utilisation

KEYPAD.-
The function of each key is listed below. See Fig.3
The electronic monitor includes an easy-to-use keypad. This keypad consists of Fan keys (E), numeric keys
(F) and function keys (G).
- Fan keys (E) – Off / On; Low (minimum speed); High (maximum speed).
- Numeric keys (F) - (1- 0) are used to enter the data requested by the monitor.
- Function keys (G) – reset; level ; level ; enter; pause; stop; quick/start are used to select a particular
exercise, enter requested data, control exercise exertion levels and to finish the exercise.
-reset.-
Reset key. This is used to erase the data that have been entered into the monitor when selecting
a program.
-level▼.-
Key for decreasing exertion level. When pressed during exercise this key will decrease the
exertion level by one machine setting. During the selection of pre-programmed profiles, it is used to move on
to the next profile screen.
-level▲.-
Key for increasing exertion levels. When pressed during exercise this key will increase the
exertion level by one machine setting. During the selection of pre-programmed profiles, it is used to move
back to the previous profile screen.
-enter.-
Selection and validation key. This is used during pre-programmed profile selection to select a
profile, confirm data that have been entered and to start the exercise. It is also used during user profile
programming to confirm the exertion level settings for each minute.
-pause.-
Pause key. If this is pressed during a session, the exercise is interrupted and the exercise
chronometer is halted. To restart the exercise chronometer press the pause key again or continue
exercising. There is a 45 second time limit in pause mode, after which the exercise will be taken as finished
and the monitor will switch itself off.
If, in pause mode, the STOP key is pressed then the exercise will be taken as finished.
-stop.-
Stop key. If this is pressed during the session, the exercise will be taken as finished and exertion
settings will drop to minimum level. A summary of all the exercise data will be displayed and it will then return
to the start screen.
Hold the STOP key down for 3 seconds in Start/Ready mode, and the console will automatically change to
off status with a beep if the POWER option under project mode is on.
-quick/start.-
Quick start key. When this key is pressed, provided that the LED on the key is flashing,
exercise will begin in manual mode.
STARTING.-
In order to switch the monitor on it is necessary to pedal so that the crank spins at 45 r.p.m, as soon as it
reaches 45 r.p.m the monitor will come on and remain on for 60 seconds so that you can program it.
You can also plug the adapter that is supplied with the machine into a mains socket, assuming that you have
chosen the ON option in the personalised settings (step 4 POWER).
Once the monitor is on it will display the profile and the letter "M" for manual on the LED array (A) Fig.2, and
the "WELCOME TO HI POWER" welcome message on the bottom alphanumeric screen (B).
You can start the program in manual mode by pressing the QUICK/START key and by pressing the keys
level▲ or level▼ keys you can increase or decrease the exertion levels.
OPERATING INSTRUCTIONS.-
STARTING THE FAN.-
The monitor on this machine is fitted with an air vent (D), Fig.1, through which a FAN provides two air
speeds, LOW and HIGH. To switch the fan on while exercising press the ON/OFF key on the keypad, Fig.3,
and the fan will start. Whenever the monitor is switched to PAUSE the fan will switch off.

SLEEP MODE:

This mode is activated if no RPM signal is received within 45 seconds when in stand-by mode. No windows
are displayed while in this mode. You have to step on the footplate to produce a signal and reopen the
display window. Sleep mode cannot be accessed if the appliance is switched on.
If the adapter is connected to the machine then the console will not switch over to sleep mode when the
POWER option under project mode is switched on. With no adapter connected, the console will switch over
to sleep mode even when it is switched ON.
.
16
SK
LINE
sportkoncept