Installation Instructions - Empire Heating Systems DVC35IPXLP-1 Instructions Pour L'installation Et Manuel Du Propriétaire

Radiateur mural à circulation forcée avec un évent direct

Masquer les pouces

Table des Matières

Les langues disponibles

Locating Wall Opening

The furnace is to be located on an outside wall. Locate wall studs

so that wall opening will be located between wall studs. The fur-

naces is 14 1/8" (358mm) in width and can be recessed between

standard 16" (406mm) on center wall stud. The wall opening re-

quired as shown in Figure 5 is a diameter of 7 1/2" (191mm).

Locate and cut wall opening. If there is insulation above the wall

opening (air inlet tube) a barrier should be installed above the wall

opening (air inlet tube) to prevent insulation from coming in con-

tact with the air inlet tube. The barrier must not penetrate into the

7-1/2" (191mm) diameter wall opening.

A template is provided in furnace carton for positioning furnace on

the wall. Also, refer to Figure 5 and Figure 7 for positioning the

furnace on wall and for locating gas line connection.

Installing Optional Side Outlets

Side outlet register, SOR-1 may be installed on one or both sides

of the furnace at the required clearances of 18" (457mm) to adja-

cent wall or combustible material as shown in Figure 6.

Turn "OFF" all electric power to the furnace.

Remove the front panel from the furnace.

Remove the (2) #8 X 3/8" (9mm) screws that attach the inner

shield cover plate to the inner shield.

Scribe a line between the four dimples on the outer casing side

to form a square.

Drill a pilot hole within the scribed square on the outer casing.

Remove the sheet metal within the scribed square with a tin

snips or comparable tool. Attention! Do not cut the electrical

wires located between the outer casing and the inner shield.

Insert the 5" x 5" (127mm x 127mm) inner boot through the

outer casing. Align the clearance holes on the inner boot with

the crew holes on the inner shield. Attach inner boot to inner

shield with (2) #8 x 3/8" (9mm) screws removed in Step 3.

Place the register over the 5 1/2" (140mm) square opening with

the louvers set for the desired direction and mark the mounting

holes using the register as a template.

Drill (2) 1/8" diameter holes in cabinet side and attach the

Installation of SOR-1 is completed.

Side outlet kit, SOK-1, 10" (254mm) boot assembly with register,

for warm air discharge into an adjoining room may be installed on

either side of the furnace at the required clearance of 4" (102mm)

to adjacent wall as shown in Figure 6.

To install SOK-1, please use step 1 through 5 in the SOR-1 in-

structions for DVC-35 furnaces. Then, use the following Steps to

complete the installation of the SOK-1.

Using the inner and outer boots as hole templates, mark and

drill (4) 1/8" (3mm) diameter holes in the inner shield and (4)

1/8" (3mm) diameter holes in the cabinet side.

Locate and cut a 6 3/4" (171mm) square opening through wall.

Attach furnace to wall (see Attaching Furnace to Wall).

With furnace in place, after checking alignment of side outlet

opening in wall and furnace, place the 9 3/8" x 9 3/8" (238mm

x (238mm) side outlet wall plate over outer boot, pass the outer

boot through the wall and attach side wall plate to furnace side

of wall with (2) #10 x 1 1/2" (38mm) provided screws.

Attach outer boot to the cabinet side with (4) #8 x 1/4" (6mm)

provided screws.

Position and attach inner boot to inner shield with (4) #8 x 1/4"

(6mm) provided screws.

Page 10