Warnings; Operation; Safety Devices - HeatStar HS1000ID Instructions D'utilisation Et Manuel Du Propriétaire

OPERATION

Before any attempt of starting the heater is made, check that
your electrical supply conforms to the data on the model plate.
Control Board
l k
M
l k
1. RESET BUTTON WITH CONTROL LAMP
2. CONTROL LAMP
3. MAIN SWITCH
4. ROOM THERMOSTAT PLUG
5. POWER CORD
Gap of Electrodes
X
Z
Models X
HS1000ID
.79in
.158in
HS2000ID
.158in
HS3000ID
.158in
HS4000ID
Clearances
Sides 2.5 ft.
Top 6 ft.
The following minimum safety clearances from materials or
objects in the surroundings of the heater must be ensured:
• Floors and ceilings must be made of fireproof materials in
the room where the heater is operated.
• The air inlet and outlet must never be blocked for any
reason.
• Install the heater on a flat, level floor in a steady position.
Fuel Fired Forced Air Indirect Construction Heater
Y
Y Z
.1 18in .256in
.098in .158in
.098in .158in
.098in .158in
Air Inlet 2.5 ft.
Air outlet 12 ft
WARNING
• DO NOT USE GASOLINE, NAPHTHA OR VOLATILE FUELS
• STOP HEATER BEFORE ADDING FUELS.
• ALWAYS FILL OUTDOORS AWAY FROM OPEN FLAME
• DO NOT USE EXTERNAL FUEL SOURCE.
• DO NOT OPERATE HEATER WHERE FLAMMABLE LIQUIDS
OR VAPORS MAY BE PRESENT.
• DO NOT START HEATER WHEN CHAMBER IS HOT
• DO NOT START HEATER WHEN EXCESS FUEL HAS
ACCUMULATED IN THE CHAMBER.
• DO NOT PLACE COOKING UTENSILS ON TOP OF THE
HEATER.
• PLUG ELECTRICAL CORD INTO A PROPERLY GROUNDED
THREE-PRONG RECEPTACLE.
The heater can only work automatically when a control device,
such as for example a thermostat or a timer, is connected to
the heater. Connection to the heater is made by removing the
socket cover(4) and inserting the thermostat plug.
To start the machine you must:
• If connected to the thermostat, turn the switch to (ON + )
• If not connected to the thermostat, turn the switch to
(ON).
When unit is started for the first time or is started after the oil
tank has been totally emptied, the flow of oil to the burner may
be impaired by air in the circuit. In this case the control box will
cut out the heater and it might be necessary to renew the starting
procedure once or twice by depressing the reset button (1).
Should the heater not start, check that oil tank
is full and depress reset button (1).
Should the heater still not work, please refer to chapter
"OBSERVED FAULTS, CAUSES AND REMEDIES".
Stopping the Heater
Set main switch (3) on "0" position or turn thermostat or other
control device on lowest setting.
The flame goes out and the fan continues to work for approx.
90sec. cooling the combustion chamber.

Safety Devices

The unit is fitted with an electronic flame control box. In case of
malfunction this box will cut in and stop the heater, at the same
time the pilot lamp in the control box reset button (1) will light
up.
Heaters are also equipped with an overheat thermostat safety
cutout which will stop the heater in case of overheating. This
thermostat will reset automatically but you will have to depress
button (1) on control box before being able to restart the
heater.
Transport
Warning
• Before making any attempt to restart heater find and
eliminate reason of overheating.
Before heater is moved it must be stopped and unplugged.
Before moving the heater wait till it has totally cooled off and
make sure oil tank cap is securely fixed.
Operating Instructions and Owner's Manual
4