Table des Matières
Publicité
YSP-500
QUICK REFERENCE GUIDE
This quick reference guide explains steps to connect a TV and a DVD player to this unit and achieve the
surround sound effects in a quick, easy manner. For detailed operation, refer to the Owner's Manual.
1
Installing this unit
Decide where to install this unit.
Install this unit where there are no objects such as furniture obstructing the path of sound beams. Otherwise, the desired
surround sound effects may not be achieved. You may install this unit in parallel with the wall or in the corner.
Install this unit in the exact center of the wall when it is
Install this unit in the corner at a 40˚ to 50˚ angle from the
measured from the left and right corners.
adjacent walls.
An object, such as furniture
An object, such as furniture
40˚ to 50˚
Front left channel
Center channel
Front right channel
Surround left channel
Surround right channel
Install this unit using a rack, etc.
Depending on your installation environment, connections with external components (see "2 Connecting external components to this unit") can be done before
installing this unit.
We recommend that you temporarily place and arrange all components in order to decide which procedure must come first.
For further information on installation, see page 13 in the Owner's Manual.
The following is an example of installing this unit in a rack.
1
2
3
Place this unit in front of
Connect this unit
Install this unit in the
the rack.
to your TV and DVD player.
rack.
y Hint
To enjoy better surround effects, place this unit on the upper shelf to keep it away from the floor.
Note
Be careful not to leave scratches on this unit or the rack.
Printed in Malaysia
WM28850 [En]
2
Connecting external components to this unit
Items used for connections and operations
in this guide
s Audio pin cable (x1)
s OSD* video pin cable (x1)
Connecting external components such as a TV or DVD player to this unit.
s Optical cable (x1)
s Digital audio pin cable (x1)
Connect your TV or DVD player to this unit using appropriate cables as shown below.
s IntelliBeam microphone (x1)
For further information on connecting other components, see pages 16 to 24 in the Owner's Manual.
s Cardboard microphone stand (x1)
s Demonstration DVD (x1)
*OSD: On-Screen Display
This connection example shows a way to connect external components such as a TV or DVD player to this unit by using the supplied cable.
Use the video pin cable supplied with your DVD player to make a video connection between your DVD player and TV.
Front left channel
Center channel
Front right channel
Surround left channel
Surround right channel
4
Installation is completed.
After all connections are complete, plug the power supply cable into the AC wall outlet.
TV
OPTICAL
ANALOG AUDIO
VIDEO
OUTPUT
INPUT
AUDIO OUTPUT
1. Pull out the cap
L
1
R
2
2. Check the direction
1
2
3
4
L
R
VCR
TV/STB
SUBWOOFER
VIDEO
TV/STB
AUX
DVD
SYSTEM
CONNECTOR
OPTICAL
COAXIAL
AUDIO INPUT
OUT
DIGITAL INPUT
Audio connection
You can enjoy the multi-channel audio from the DVD player and the analog/digital audio from the TV.
DVD player
Video connection
COAXIAL
AUDIO OUTPUT
Optical cable
Pull out the cap
before connecting
the optical cable,
and then check the
direction to insert
the cable.
YSP-500
L
R
VCR
TV/STB
SUBWOOFER
VIDEO
TV/STB
AUX
DVD
SYSTEM
OPTICAL
COAXIAL
CONNECTOR
AUDIO INPUT
OUT
DIGITAL INPUT
If a subwoofer is connected to this unit, turn on the power of your
subwoofer and then carry out the AUTO SETUP procedure (see the
backside) or select "SWFR" for "BASS OUT" in "SUBWOOFER SET" (see
page 62 in the Owner's Manual).
System connection
Subwoofer
Connect the supplied cables in the following order.
1 Audio pin cable
(Outputs
TV analog audio sounds
from this unit)
2 OSD video pin cable
(Displays
the YSP-500 menu screen
on the TV)
3 Optical cable
(Outputs
TV digital audio sounds
from this unit)
4 Digital audio pin cable
(Outputs
DVD digital audio sounds
from this unit)
Note
Check whether the digital audio output of your TV and DVD
player is turned on.
To the AC wall
outlet
Do not plug the power
supply cable into an AC
wall outlet until all
connections are complete.
If you have connected external components,
follow the steps on the backside to start the
Continued
on the back
AUTO SETUP procedure.
C2007
All rights reserved.
Publicité
Table des Matières
