Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
•
Enable Panic function: this function activates Relay 2 on the number keypad (to which an alarm system
can be connected) when the specified character at the end of an authorised code is entered (not enabled
by default).
•
Panic button: character to be entered at the end of an authorised code in order to activate Relay 2 on the
number keypad (key 3 by default).
•
Maximum number of errors: the keypad locks when the maximum programmed number of incorrect
access codes has been entered (default: 3). You need to wait 15 seconds before you can enter a new
code.
•
Enable Wiegand mode: this function allows the use of an external Wiegand interface to manage access
control (disabled by default).
•
Maximum Wiegand response time (ms): set the maximum wait time for the Wiegand interface (from 0 to
600 ms, default: 500 ms).
•
Enable audio message playback on key press: function allowing playback of the corresponding audio
message when each button is pressed (e.g. if you press 2 on the number keypad, audio message "two"
will be played; disabled by default). Only with audio or audio/video module.
•
System type: select the type of system in which the number keypad is installed (Simplebus or ViP).
•
Supercode: code (always containing 6 digits) that provides authorisation to program the keypad (default:
778899).
•
Program universal code: enable universal code programming. The universal access code always allows
access, without time band constraints, etc.
•
Default action for codes entered via keypad and/or in the directory without specifying Action 1: this
is the action assigned to the codes entered directly via the number keypad, or entered in the Directory if
no parameter is specified in the "Action 1" menu. NOTE: if this code is changed, codes entered after the
change will behave as thou they have been programmed, while those entered previously will not change
their behaviour.
◊
Relay 1: the access code activates Relay 1 on the number keypad.
◊
Relay 2: the access code activates Relay 2 on the number keypad.
◊
Relay 1 & Relay 2: the access code activates Relay 1 and Relay 2 on the number keypad.
◊
Module SE output: the access code activates the SE output for the audio or audio/video module to
which the number keypad is connected (default).
◊
Module relay output: the access code activates the relay output for the audio or audio/video module to
which the number keypad is connected.
◊
Actuator: the access code activates an actuator in the system.
◊
Actuator address: enter the address of the actuator art. 1256 (simplebus) to be activated (this menu
only appears if the "Actuator" option has been selected in the "Default action for codes entered via
keypad and/or in the directory without specifying Action 1" menu).
•
Access code validity: define the maximum number of uses permitted for the programmed access code
(from 0 to 9, default: 0, valid permanently).
•
Buzzer on key press: a tone sounds every time a key on the number keypad is pressed (enabled by
default).
•
Buzzer sound level: adjust the volume of the tone that sounds every time a key on the number keypad is
pressed (from 1 to 10, default: 10, maximum level).
•
Backlight adjustment: adjust the brightness of the number keypad backlighting (from 0 to 100, default:
50).
•
Enable calls: the number keypad can also be used to call users when the code is known. The code may
consist of up to 3 digits (enabled by default).
•
Key button followed by the code mode: standard access code usage requires entry of a code on the
keypad, when the last digit is entered the programmed output is activated. However, when this mode is
enabled, before entering the code you need to press the "Key" button (disabled by default).
Action 1 (2, 3, 4) Universal Code
The universal access code can be assigned up to 4 different actions which will be carried out consecutively.
•
Action
◊
Audio call: when the universal access code is entered on the number keypad, an audio call is made to
the address entered in the "Address" field.
•
Address: select the address to which you want to make the audio call (from 1 to 240).
•
Number of calls: select the number of calls to make to the address entered in the "Address" field (System
settings or from 1 to 10).
10
Publicité
Table des Matières
