Yamaha CL5 Manuel De Référence page 268

 REV+SYMPHO.
One input, two output reverb and symphonic effects in parallel.
Parameter Range
REV TIME 0.3-99.0 s Reverb time
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
HI. RATIO 0.1-1.0 High-frequency reverb time ratio
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reverb density
Reverb and symphonic balance
REV/SYM 0-100%
(0% = all reverb, 100% = all symphonic)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
MOD. DLY 0.0-500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
*1
NOTE Used in conjunction with TEMPO to determine FREQ
*1.
 REVSYMPHO.
One input, two output reverb and symphonic effects in series.
Parameter Range
REV TIME 0.3-99.0 s Reverb time
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
HI. RATIO 0.1-1.0 High-frequency reverb time ratio
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reverb density
Reverb and symphonic reverb balance
REV.BAL 0-100%
(0% = all symphonic reverb, 100% = all reverb)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
MOD. DLY 0.0-500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
*1
NOTE Used in conjunction with TEMPO to determine FREQ
*1.
Description
Description
15
 REVPAN
This is a 1-in/2-out series-connected reverb and auto-pan effect.
Parameter Range
REV TIME 0.3-99.0 s Reverb time
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
HI. RATIO 0.1-1.0 High-frequency reverb time ratio
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reverb density
Reverb and panned reverb balance (0% = all panned reverb, 100% = all
REV.BAL 0-100%
reverb)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
*1
DIR. Panning direction
WAVE Sine, Tri, Square Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
*2
NOTE Used in conjunction with TEMPO to determine FREQ
*1. LR, LR, LR, Turn L, Turn R
*2.
 DELAY+ER.
One input, two output delay and early reflections effects in parallel.
Parameter Range
DELAY L 0.0-1000.0 ms Left channel delay time
DELAY R 0.0-1000.0 ms Right channel delay time
FB. DLY 0.0-1000.0 ms Feedback delay time
Feedback gain (plus values for normal-phase feedback, minus values for
FB. GAIN -99 to +99%
reverse-phase feedback)
HI. RATIO 0.1-1.0 High-frequency feedback ratio
Delay and early reflections balance (0% = all delay, 100% = all early
DLY/ER 0-100%
reflections)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
S-Hall, L-Hall, Random,
TYPE Type of early reflection simulation
Revers, Plate, Spring
ROOMSIZE 0.1-20.0 Reflection spacing
LIVENESS 0-10 Early reflections decay characteristics (0 = dead, 10 = live)
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reflection density
ER NUM. 1-19 Number of early reflections
SYNC OFF/ON Tempo parameter sync on/off
*1
NOTE L Used in conjunction with TEMPO to determine left channel DELAY
NOTE R Used in conjunction with TEMPO to determine right channel DELAY
*1
Used in conjunction with TEMPO to determine feedback DELAY
NOTE FB *1
*1.
Description
Description
(Maximum value depends on the tempo setting)
Data List