Virutex UC16K Mode D'emploi page 5

door is already mounted on the frame, place wedges
underneath it to prevent it from moving.
- Place the lock against the door at the desired height
from the floor and mark the centre of the recess on
the edge with a pencil.
- Place the lock mortising accessory on the door,
so that the centre mark of the base "B" (Fig. 1) will
align with the mark made.
- Fasten the clamp vises "G", alternately turning the
two crank handles "H" (Fig. 4).
8. ASSEMBLING THE CUTTING
TOOL AND THE TEMPLATE GUIDE
Before carrying out this operation,
check that the trimmer is disconnected
from the mains.
- Remove the nut and the fastening clamp of the
cutting accessory and replace it with the jointing
bit, model 1640157, "I" (Fig. 5).
- Place the template guide "J" on the base "K" and
fasten it with the two screws.
9. TRIMMING OF RECESSES ON
DOOR EDGE AND FRONT
a) To trim recesses on the door, loosen the two levers
"L" (Fig. 6) and move the base "B" (Fig. 6) sideways until
the template matches the centre with the lock recess
on the door. Then, with the help of the millimetre
rule "M" (Fig. 6), ensure that the base "B" (Fig. 6) is
well supported on the edge of the door. Press down
the two levers "L" (Fig. 6), adjust the cutting depth
of the accessory and begin trimming.
Before removing the machine from
the accessory, place the trimmer at its
highest position so that the accessory
is hidden in the base "K" (Fig. 5), thus
preventing accidental contact with
the template.
b) To carry out recesses on the front, loosen the
two levers "L" (Fig. 6) and move the base "B" (Fig. 6)
completely towards one side of the accessory so that
it does not interfere with the trimming process on
each front section. For a perfect finish, we recommend
that you trim only half way through the door, for
each front section.
10. PLACING THE ACCESSORY ON A FRAME
- Replace the template for the edge used to trim the
door with the appropriate template for the frame.
- To trim recesses on a frame, first remove the side
holders of the templates "F" (Fig. 3). Simply loosen
the two levers "N" (Fig. 3) and withdraw the entire
unit.
- Place the accessory on the frame so that the centre
mark of the base "B" (Fig. 2) is at the same height as
that used for the door. Fix the clamp vises "G" (Fig.
7) firmly on the frame, turning the crank handles
"H" (Fig. 7).
11. TRIMMING RECESSES ON A FRAME
Loosen the two levers "L" (Fig. 6) and adjust the
accessory to the frame, following the instructions
given in Section 9 about the trimming process on
a door.
12. PRODUCTION TRIMMING
ON SEVERAL DOORS
- Should you wish to trim recesses on several doors and
position the locks at the same height, we recommend
that you use the height bars "O" (Fig. 8).
- Once you have decided the height of the lock on the
first door and placed the accessory in the trimming
position, mount the height bars and insert them
in the clamp vise apertures "P", so that the limiter
disc "Q" has its limit at the upper edge of the door.
Fix the height bars in this position with the Allen
wrench a/f 4 mm.
- For the following door, all you will need to do
is place the limiter disc "Q" so that it rests on the
upper edge of the door and fix the clamp vises in
this position. In this way, all the recesses will be at
the same height.
- If so desired, the height bars can also be used
without the limiter disc as a height reference relative
to the floor.
13. WARRANTY
All VIRUTEX machines and accessories are covered by
a warranty that is good for one year following their
supplying. The warranty does not cover damage that
has occurred as a result of tampering or improper
handling. Neither does it cover the normal wear and
tear of the machine. All repairs should be carried out by
the official VIRUTEX technical assistance service.
VIRUTEX reserves the right to modify its products
5