Dyson AB09 Manuel D'installation page 33

BEFORE INSTALLING OR USING THIS UNIT
READ ALL INSTRUCTIONS AND CUSTOMARY
MARKINGS IN THIS INSTALLATION GUIDE AND
THE OWNERS MANUAL.
WARNING
Installation work, plumbing and electrical wiring must be
done by qualified person(s) in accordance with all federal,
state and local laws and applicable codes and standards,
including fire-rated construction.
WARNING
Risk of electric shock! If casing is removed or handled
improperly the internal components of the unit may cause
harm or become permanently damaged.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
BEFORE INSTALLATION
Before beginning any installation work you must confirm the
following.
WIRING
• Check that the electrical supply corresponds to that shown on
the rating plate. If the unit is connected to any electrical supply
other than stated on the rating plate of the unit, permanent
damage or improper/unsafe operation of the unit may result.
• A means for all-pole disconnection must be incorporated into
fixed wiring, in accordance with local wiring regulations.
• When connecting the unit to the electricity supply use electrical
wiring in accordance with all federal, state and local laws
and applicable codes and standards, including fire-rated
construction.
• Connect the electricity supply using suitable conduit and
electrical fittings. Ensure that the conduit and wires are long
enough to connect to the backplate and the terminal block.
• The unit requires a 15 amp circuit breaker with a dedicated line
and neutral.
SAFETY
• Isolate the power before installation or service.
INSTALLATION
• Make sure that the unit is installed in compliance with all
building codes and/or regulations.
• The main unit must be mounted on a flat vertical wall capable of
supporting the full weight of the unit.
• Use hardware as specified in this installation guide.
• Ensure no pipe work (gas, water, air) or electrical cables, wires
or ductwork are located directly behind the drilling/mounting
area.
• Dyson recommends the use of protective clothing, eyeware and
materials when installing/repairing as necessary.
• This appliance is intended to be permanently connected to the
water mains.
• This product should be installed with a device in accordance
with local regulations or for the US with ASSE 1070 so that
hot water delivered from this product is limited to a maximum
temperature of 49°C (120ºF).
• Do not use sealant when fixing the unit to the wall.
• Do not place the downward facing sensor of the tap over a
reflective surface, such as the drainage hole.
DO NOT USE ANY PRESSURE WASHING EQUIPMENT
FOR CLEANING ON OR NEAR THIS UNIT.
WARNING
LOCATION
• The unit is designed for dry, internal locations only.
• Consult local and national accessibility codes and regulations
for relevant installation guidelines. Conformity and compliance
is the responsibility of the installer.
• Ensure the required electricity and mixed feed water supplies are
available for later connection.
• Water pressure must be: maximum 116psi (8bar/0.8Mpa) and
minimum 14.5psi (1bar/0.1Mpa).
• The sink should not be fitted with a drain plug.
• When drilling holes, follow the instructions of the manufacturer
of the work surface.
• This tap hand dryer is certified by HACCP International for
use in washrooms and food preparation environments, if it is
installed at least 2.5 metres from uncovered food.
• If you are installing this tap hand dryer in a food handling or
food manufacturing environment,
please contact the Dyson Helpline for the specialist installation
guide that supports this.
WARNING
This unit contains substances known to the state of California
to cause cancer, birth defects and other reproductive harm.
Wash hand after installation or repair of this unit.
25
IMPORTANT
• Please refer to the Owner's Manual for details of the limited
warranty.
• Dyson will not be held liable for any damage to property or
personal injury as a failure to comply with the instructions
contained herein.
USES
LEA Y GUARDE ESTAS
INSTRUCCIONES
INSTRUCCIONES
IMPORTANTES DE
SEGURIDAD
ANTES DE INSTALAR O USAR LA UNIDAD, LEA
TODAS LAS INSTRUCCIONES Y SEÑALES DE
ADVERTENCIA EN ESTA GUÍA DE INSTALACIÓN
Y EN EL MANUAL DEL PROPIETARIO.
ADVERTENCIA
El trabajo de instalación, colocación de cañerías y conexión
eléctrica debe realizarlo una persona calificada conforme las
leyes locales, estatales y federales y los estándares y códigos
aplicables, incluso las regulaciones relacionadas con la
construcción ignífuga.
ADVERTENCIA
Riesgo de choque eléctrico Si la carcasa se quita o se maneja
incorrectamente, las piezas internas de la unidad pueden
causar daños o deteriorarse de manera permanente.
ADVERTENCIA
PARA REDUCIR EL RIESGO DE INCENDIOS,
DESCARGAS ELÉCTRICAS O LESIONES
PERSONALES, OBSERVE LO SIGUIENTE:
ANTES DE LA INSTALACIÓN
Antes de comenzar la instalación, debe confirmar lo siguiente: