steute RF Rx EN868 TCP/IP Instructions De Montage Et De Câblage page 9

RF Rx EN868 TCP/IP / RF Rx SW868/SW915/SW917/SW922 TCP/IP V2
//
Montage- und Anschlussanleitung / Funk-Empfänger
Mounting and wiring instructions / Wireless receiver
Instructions de montage et de câblage / Récepteur sans fil
Istruzioni di montaggio e collegamento / Ricevitore wireless
Instruções de montagem e instalação / Receptor sem fio
Инструкция по монтажу и подключению / Радиоприемник
English
Mounting and wiring
The Gateway is connected to a network switch/terminal equipment via
an 8-pole shielded RJ-45 connector, according to the 10/100 Base-T
standard. The cable must at least conform to category 5/5e, be equip-
ped with outer shielding and twisted pair wires (SF/UTP) and must not
exceed a maximum length of 100 m. With direct connection to terminal
equipment using the auto-MDI(X) function of the Gateway, no crossover
cable is required.
Antenna
Use suitable antennas only:
Device Antenna
SW868 RF magnet antenna 5dBi SMA
SW922 plug-in connector straight 1.5 m
EN868
SW868 RF magnet antenna 2dBi SMA
SW922 plug-in connector straight 2 m
EN868
SW868 RF magnet antenna SMA
SW922 plug-in connector straight 2.5 m
EN868
SW868 RF magnet antenna 5dBi TNC plug-
EN868 in connector IP65 3,6 m
EN868 RF high gain antenna 868MHz
SW915 RF magnet antenna 2dBi R-SMA
SW917 plug-in connector straight 2 m
SW915 RF magnet antenna 5dBi R-SMA
SW917 plug-in connector straight 3.6 m
Mount the antenna on a metal plate. The metal plate serves as HF
counterweight. Minimum size of metal plate: 250 x 250 mm. Observe
minimum sideways distance to nearest wall or disturbance source:
300 mm. Do not bend or clamp the cable. Minimum bending range of
cable: >25 mm.
Design of wireless range
The radio signal (wireless signal) is attenuated on the way from the
transmitter to the receiver. In addition, the radio signal (wireless sig-
nal) is attenuated/influenced by obstacles. The degree of attenuation
depends on the material of the obstacle.
The following tables serve as a guide.
Penetration of radio signals:
Material
wood, gypsum, glas uncoated
brick stone, press boards
armoured concrete
metal, aluminium lamination, water
Typical ranges:
Place of use
Line of sight in free field (LR)
Line of sight in free field (ULR)
Line of sight in free field (SW922 LR):
Line of sight in free field (SW922 ULR):
Line of sight indoors (LR)
Line of sight indoors (ULR)
Line of sight indoors (SW922 LR)
Line of sight indoors (SW922 ULR)
Mat. No.
Line of sight in free field (EN868)
1188958
Line of sight in walkways (EN868):
Line of sight in halls (EN868):
To obtain the maximum range use the specified antennas. With other
1470770
antennas, the maximum range may differ.
N.B.
1186143
The electrical connection may only be carried out by authorised per-
sonnel. The radio receiver must not be used in connection with devices
that may directly or indirectly serve health- or life-saving purposes or
cause hazards by operation to human beings, animals or asset values.
1275629
Subject to technical modifications.
1187161
Start-up
1470773
The green LED MD (Mode) lights up permanently after power supply.
The yellow LED 1 is off and flashes fast when receiving a valid
1188987
wireless signal.
Reset device configuration
The device configuration is reset to delivery status (fixed IP) by press-
ing the push-button »S1« for 10 s. (Mode LED flashes slowly, 2 Hz).
- IP address:
- Network template:
- Gateway:
- Port:
- Default password restored
Restore delivery status
The Gateway is reset to delivery status by pressing the push-button
»S1« for 20 s. (Further 10 s after reset of device configuration). (Mode
LED flashes fast, 5 Hz).
- Default device configuration (see above)
- List of taught in switches is empty
Penetration
90...100 %
65...95 %
10...90 %
0...10 %
9 / 52
Wireless range
(approx.)
450 m
700 m
150 m
230 m
40 m
50 m
20 m
25 m
300 m
30 m
100 m
192.168.0.123
255.255.255.0
192.168.0.1
64210