Energy V-SW10 Mode D'emploi page 4

terMInOLOGy anD COntrOLS
STATUS INDICATOR– The LED found on the front panel will illuminate in blue
u
when the subwoofer is functioning. If the unit is in Auto mode and is not
receiving a signal, the light will remain off.
v SPEAKER LEVEL IN – The Speaker Level inputs are designed to be used on
receivers or amplifiers that do not incorporate any RCA type subwoofer
outputs. If your receiver is equipped with an RCA type subwoofer output,
these speaker level inputs should not be utilized.
PHASE – This switch allows for the adjustment of the phase of the subwoofer,
w
in relation to the speakers used in your system, either 0 or 180 degrees.
VOLUME – This knob can be adjusted to control the level of output
x
from your subwoofer. The level chosen should allow the subwoofer to blend
its output with that of the rest of your audio system.
LOW-PASS FILTER – This control allows for the adjustment of the low-pass
y
filter. Adjustments can infinitely be made from 40Hz to 120Hz. This will
determine the highest frequency that the subwoofer will reproduce.
LINE IN/SUB IN – These inputs are an RCA type LFE/stereo/mono input. If you
z
are connecting your subwoofer to a pre-amp/processor with a LFE or
Subwoofer pre-amp output, connect a single RCA cable to the LFE/Left input.
POWER MODE – This switch can be set to either On, Off or Auto. If the switch
{
is in the Off position, the subwoofer will not power up. If the switch is in the
On position, it will constantly remain on. If the switch is set to the Auto
position, when a signal is present the subwoofer will turn on and will
automatically turn off several minutes after a signal is no longer present.
POWER CORD CONNECTOR – Connect the power cord from your AC outlet
|
to this input. Connecting your subwoofer to a surge protector or line
conditioner is always recommended. Do not connect the power cord to the
switched or unswitched outlet of your receiver as this could damage your
subwoofer and receiver.
V-SW10
V - SW10
This device complies with Part 15 of Designed and Engineered in the USA
the FCC Rules. Operation is subject Conçus dans les États-Unis
to the following two conditions: Made in China / F
(1) this device may not cause
harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause
AVIS
undesired operation.
CAUTION:
FOR CONTINUED PROTECTION AGAINST
RISK OF FIRE, REPLACE ONLY WITH
E
SAM TYPE FUSE AND RATING.
ATTENTION:
R
UTILISER UN FUSIBLE DE RECHANGE
D E M E M E T Y P E E T C A L I B R E .
COnneCtInG yOUr enerGy SUBWOOfer
CAUTION: All power should be turned off to your system before any
connections are made. Careful attention should be taken to ensure that all
electronic components are not connected to an AC source. Not doing so
could result in potential damage to the system.
MetHOD 1 – RCA – SUB IN FOR HOME THEATER OR LFE APPLICATIONS
1. On the rear of the receiver/pre-amp there should be a single RCA type jack
marked "Subwoofer/Pre-Amp Out". Connect a single RCA cable from that jack
to the z LINE IN/SUB IN on the rear of the subwoofer. A standard male to male
RCA cable is needed.
2. After connecting the single z LINE IN/SUB INconnection, plug your ENERGY
subwoofer into an AC outlet. Do not use the AC outlet on the rear of your
receiver. After plugging in the unit, switch the Main Power to On.
3. See Final System Adjustments, below.
MetHOD 2 – SPEAKER LEVEL – FOR MUSIC APPLICATIONS
1. The other way to connect your subwoofer to your receiver is using a speaker
wire connection, by simply connecting the speaker wires from the Front Left
and Right Speaker Outputs on your receiver to the Left and Right v SPEAKER
LEVEL IN on rear of the subwoofer. It is imperative that speaker polarities be
maintained, one must connect the positive and negative wires to the appro-
priate positive and negative terminals. Failure to do so will result in an out of
phase connection, severely limiting the amount of bass in your system.
2. After connecting the v SPEAKER LEVEL IN (speaker wire) between your
receiver and subwoofer, ensure no fray wires are touching, as this could cause
180 0
PHASE
Left
VOLUME
Min Max
Right
SPEAKER LOW-PASS
LEVEL IN FILTER
40Hz 120Hz
LINE IN /
SUB IN
POWER
MODE
Auto
On
Off
abriqué en Chine