Optional Accessories - Makita DRC200 Manuel D'instructions

TROUBLE SHOOTING
NOTE: If the problem persists after the remedial
action is taken, consult your nearest Makita Service
Center.
Symptom
The lamps do
not light up
when you press
the button.
Install the battery cartridges correctly.
The Robotic
Fully charge the battery cartridges.
Cleaner does not
Press the
operate when you
Robotic Cleaner ON.
press the button
on the Robotic
Cleaner or the
remote control.
If the
lamp,
or
up or flashes, see "RESTORING THE
ROBOTIC CLEANER" to resolve the
The Robotic
problem.
Cleaner does not
If the pilot lamp flashes slowly, press
operate.
and hold the
the Robotic Cleaner until all indicators
go off, or press the
button on the remote control to clear
the timer.
The Robotic
Cleaner starts
• The auto-on timer has been activated.
operation
automatically.
Turn the Robotic Cleaner OFF, and
then remove any cords, strings, etc.
The Robotic
from the drive wheels.
Cleaner stops
If the Robotic Cleaner has gotten
operation during
stuck on a barrier or other obstacle,
cleaning.
move the Robotic Cleaner to a
different location.
• If an obstacle is detected, the Robotic
Cleaner will slow down as it takes time
The cruising speed
to calculate a traveling direction. This
is not constant.
is not a malfunction of the Robotic
Cleaner.
The Robotic Turn the Robotic Cleaner OFF, and
Cleaner does not then remove any foreign objects
travel straight tangled in the drive wheels.
forward. Clean the ultrasonic sensors.
The Robotic
Cleaner is hitting
obstacles more Clean the ultrasonic sensors.
frequently than
before.
Clean the cliff sensors.
The Robotic
• The Robotic Cleaner may not avoid
Cleaner falls down
differences in level of 5.5 cm (2-3/16")
stairs or to a lower
or less. This is not a malfunction of the
floor.
Robotic Cleaner.
The operating Empty the dust box and clean the
sound is louder filter, the side brushes, and the main
than usual. brush.
Cause/Remedy
button to turn the
Troubleshooting
Filter maintenance lamp,
Brush maintenance lamp lights
POWER button on
POWER OFF
The suction power
is not strong
enough to capture
dust and dirt.
The side brushes
fall off.
The side brushes
do not rotate
or rotate with
difficulty.
The exhaust air
smells.
The remote control
does not work.
The auto-on timer
does not work.
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments are
recommended for use with your Makita tool specified
in this manual. The use of any other accessories or
attachments might present a risk of injury to persons.
Only use the accessory or attachment for its stated
purpose.
• Boundary tape
• Side brush
• Main brush
• Bottom plate
• Filter
• Makita genuine battery and charger
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
14 ENGLISH
Empty the dust box and clean the
filter.
Press the Vacuum button on the
Robotic Cleaner or on the remote
control to turn ON the vacuum fan.
Install the side brushes correctly
(Fig. A).
Clean the side brushes and the main
brush.
Install the main brush and the plate
correctly (Fig. N).
Empty the dust box and clean the
filter.
Install the remote control batteries
correctly (Fig. E).
Replace the batteries with new ones.
Press the POWER button on the
Robotic Cleaner to turn it ON.
Move closer to the Robotic Cleaner
or remove obstacles between the
Robotic Cleaner and the remote
control.
Stop using the Robotic Cleaner near
or move it away from equipment that
uses radio frequencies in the 2.4 GHz
band (kitchen microwaves, Bluetooth
devices, Wi-Fi devices, etc.).
Turn the Robotic Cleaner OFF and
then ON.
Use fully charged battery cartridges.
Reactivate the auto-on timer.