Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Manually pull the first nails in the coil toward the tool nose, ensuring that the nails heads are located in the upper groove and
the collation wires are located in the proper transport channels.
For the plastic sheet collated nails: when the feeder door is closed, make sure not to squeeze the plastic band. This band
must come out freely from the hollow in the central area of the nosepiece. The nail heads must be housed inside the upper
channel and above the upper edge of the feeder door.
Engage the first nail between the feeder teeth. Close the magazine cover and check that the plastic tooth of the magazine
cover is hooked on the vertical side of the holder. If the plastic tooth is not secured, the nailer may jam or allow the magazine
to open when the tool is placed in a vertical or upside-down position.
2.5) ANGLE BRADDERS WITH REAR LOADING ( "OTHER")
After a strip of brads is inserted into the rear channel of the magazine, pull the pusher back keeping the push button down
until the pusher is positioned behind the strip. Release then the pusher, which gently will position the strip into the tool nose.
3) CLEARING JAMS
Always disconnect the tool from the air supply before attempting to clear a jammed fastener.
Extract the jammed fastener using a pliers or screwdriver, taking care to prevent damage to tool components. Use a spare
driver blade to tap the tool driver blade back up if the nail is jammed in the tool nose.
Do not use excessive force to free a jammed fastener. Disassemble the tool to gain access to the area of the jam, and
carefully work the jammed fastener free.
NOTE: Some tool models may have design modifications that permit quick release of jammed fasteners. Before using hand
tools to clear jams on these tools, first attempt to release the fastener using the features built into these tools.
D) TECHNICAL FEATURES AND ACCESSORIES
For additional data and specific details concerning the tool, see the folder included at the end of this manual, which contains
the following information:
Page 1)
Schematic drawing of the tool
Page 2)
Declaration of conformity
Page 3)
Technical table with the tool features and required fasteners specifications
Data on mechanical impacts and noise emissions
Page 4)
List of components and recommended spare parts
E) AIR SUPPLY AND CONNECTION
ACCESSORIES: Air fitting at the tool inlet must be a male free-flow quick disconnect type that allows air in the tool to be
vented out freely when the air supply hose is disconnected from the tool.
HOSES: The air supply hose to the tool must have a minimum inside diameter of 1/4" (6.3 mm), on hoses up to 15 feet (5 m).
Where longer hose runs are necessary, the inside diameter of the hose must be increased to provide adequate airflow to the
tool. Use 5/16" (8 mm) inside diameters for lengths up to 25 feet (8 m). 3/8" (9.5 mm) inside diameter for lengths up to 50 feet
(16 m). Always consider the pressure losses resulting from using an excessively long hose.
SUPPLY: Clean, regulated, lubricated, compressed air. This requires a compressor with an air filter, an oilier (lubricator), and
a pressure regulator to control air pressure being delivered to the tool. Make sure that the minimum air pressure delivered by
the compressor is adequate to drive the fasteners being used, since tank pressure will steadily decrease until the low
pressure switch on the compressor is activated.
F) MAINTENANCE
- Do not fire the tool while empty. Firing an empty tool places extra stress on tool components, and may lead to premature
failure.
- Wipe tool clean daily and inspect for wear. Use non-flammable cleaning solution only if necessary. Do not soak. CAUTION:
such solutions may damage O-rings and other tool parts.
- Drain the moisture from the air filter of the compressor filter - regulator - lubricator assembly periodically. Allowing water to
accumulate can result in moisture build up in tool, causing corrosion and reduced power.
- Use only pneumatic tool lubricating oil for tool lubrication. Other types of oils may froth and have a negative effect on tool
performance. Adjust the lubrication to provide a light mist of oil (2-3 drops per 4 hours).
- Contact the Manufacturer, or your local distributor for replacement parts and service. Using unauthorized parts or service
can result in voiding of warranty and damage to other tool components. The use of improper parts may also create a hazard,
and result in injury to the tool operator or bystanders.
- Cover air inlet when storing tool for long periods, and protect tool from exposure to extreme temperature and moisture.
Exposure to temperature extremes can cause condensation inside the tool and result in corrosion, or may affect elastic
capabilities of some components.
7
Publicité
Table des Matières
