Berner BPT-RCN-19-45-15 Manuel D'utilisation Et Entretien page 15

C) TOOL USE
THE TOOL MUST BE USED ONLY FOR THE PURPOSE FOR WHICH IT WAS DESIGNED.
Before attempting to operate the tool, you must read and become familiar with all operating and safety instructions
included in this manual. Do not use the tool if you do not understand these safety and operating instructions.
Contact your local distributor, the Manufacturer, or call the Customer Service Desk for assistance. See the back of
this manual for details.
1) MAKE SURE THAT:
- The correct fastener for the application has been selected
- The fastener meets the tool manufacturer's fastener specifications
- All required personal protective equipment is available
- The compressed air system meets all tool and safety requirements
2) LOADING OPERATIONS
Do not load fasteners with trigger depressed.
See the schematic view of the tool for reference on the following fastener loading procedures:
2.1) BOTTOM LOADING
Depress the catch in the back of the magazine. Pull the slider back to open the magazine, or tilt the tool up and let the
magazine slide open. Insert a strip of fasteners into the magazine, placing the crown up at the top of the loader. Push the
slider forward until the catch engages and locks the magazine closed.
Pinners and Corrugated Fasteners with a system to adjust the fastener lengths
Pinners: to open the magazine, pull the release lever using the little finger of the same hand used to hold the tool. Remove
the red plastic stop from the rear of the loader, and pull the slider out. Make sure that the loader insert lever in the rail is set to
the correct position for the pin length being used (see the label on the back of the tool for details. Insert a strip of pins into the
loader with points facing down. Push the slider forward until the catch engages. Reinsert the red magazine stop into its rear
seat in the holder.
Corrugated fasteners (CF): press latch and open magazine rail. With the latch still pressed, move the adjustment insert to
the appropriate slot for the length of the fastener to be used. Release latch and close the magazine rail.
Failure to position the insert correctly could cause the tool to jam repeatedly.
2.2) TOP LOADING
Pull the pusher back to the rear of the magazine and rotate it until the guide tab engages in the cut-out.
Place staples over the loader rail. For Combi tools: insert T-nails and pins in the opening of the loader rail. Pull the pusher
back slightly and rotate it downward so that the guide tab clears the cut-out. Gently move the pusher forward as far as it goes,
so the fasteners touch the tool nose. Do not allow the pusher to fly forward freely, as this can break the fastener strip, and
result in jamming of the tool.
"RHN" and "HHN" Strip Nailers
Pull the nail pusher back, until it latches behind the spring-loaded pin at the back of the magazine.
Insert the nail strips in the slot at the top of the magazine, and slide the strips forward toward the tool nose.
Pull the pusher back and press the spring loaded button on the outside of the magazine to release it, and slide the pusher
forward until it comes to rest against the nails.
Do not allow the pusher to fly forward freely, as this could damage the strips and cause jamming.
2.3) SIDE LOADING
Bradders (magazine in extruded aluminium)
Depress the catch and gently pull back on the slider. Insert one or two strips of brads into the loader with the points resting on
the bottom of the track. The brad head should fit into one of the grooves in the loader. If this is not the case, raise the strip
slightly until the heads are properly housed in the grooves.
Close the slider gently to prevent the strips from over-riding each other, and engage the slider with the catch.
Finish Nailers and NT Nailers (with magnetic strip magazine)
Depress the magazine catch at the rear of the magazine and gently pull the slider back. Insert a strip of fasteners, placing the
heads in the driving channel at the top of the loader. Slide the strip forward into the tool nose, and gently lock the slider.
On the angle bradders, after locking the slider, release the pusher catch from its stop at the back of the slider and position it
gently until it touches the brads.
2.4) COIL NAILERS
Open the door latch and the feeder door. Lift the magazine cover and check the nail plate to make sure it is positioned
correctly for the nail length being used.
To adjust the nail plate
- of the light coil nailers up to 65 mm / 2 ½" (up to the body type 45), press the knob down and slightly rotate it while lifting it
up or pushing it down. Check for correct position and load the coil into the magazine.
- starting from the 65 mm / 2 ½" coil nailer for heavy applications (on 5 and 6 body), lift the knob and slightly rotate it. Position
the nail plate so that it rests on the notches according to the desired nail length.
6