User Information; Intended Use; Fire Protection Properties; Customer Service And Spare Parts - HellermannTyton SpotClip-Plate Manuel D'utilisation

User information

1 User information
These operating instructions only apply for the products
SpotClip-Plate and SpotClip-Caps and are intended for
the user. The user must carefully read and understand
the operating instructions before commissioning the
products.
The addresses of the respective HellermannTyton country
representatives are listed at the end of these operating
instructions.

1 .1 Intended use

The SpotClip-Plate was specially developed for
installation in ceiling grids to prevent damage or cracks
to the ceiling tiles caused by the weight of heavy lights.
Sized 592 mm x 592 mm, the SpotClip-Plate is suitable
for ceiling grids with a side length of 600 mm. The most
common light diameters from 75 mm to 314 mm are
pre-punched on the SpotClip-Plate. The 8 stays can
simply be cut using a handsaw.
The SpotClip-Plate can be used in combination with
SpotClip-Caps and IRL tubes, to maintain a safety
distance between the spotlight, the damp-proof foil and
the insulating material. A combination of SpotClip-Plate
and SpotClip-Kit is also possible for such an application.
The three possible combinations are listed under
point 5.4 and permit sufficient air circulation for proper
operation. This reduces the risk of overheating and fire
hazard. It also increases the service life of the lights.
The SpotClip-Plate and SpotClip-Caps products are made
of a non-flammable, heat-stabilised polyamide.
The products must only be used for the purpose
described in these operating instructions. The products
may only be used if they are in a technically perfect
condition, as intended, with full awareness of the safety
aspects and hazards, and in compliance with the
operating instructions.
There is no information concerning the SpotClip-Kit in these
operating instructions. For more extensive information in this
regard, refer to the SpotClip-Kit operating instructions.

1 .2 Fire protection properties

The SpotClip-Plate and SpotClip-Caps satisfy the
requirements stipulated in UL94 V2 at 1.5 mm wall
thickness. The two products have been tested in
accordance with the filament test (GWT) at 960 °C as
specified in the standards EN 60598-1 and
EN 60598-2-2. EN 13501-1 A2 s1 d0 applies for the
insulating materials and damp-proof foils or vapour
barriers. Use only insulating materials and damp-proof
foils or vapour barriers of low flammability, which do not
emit smoke in the case of fire and do not drip.

1 .3 Customer service and spare parts

If you have any questions or suggestions, please contact
HellermannTyton in your country. The contact
information is listed at the end of these operating
instructions.
4
Operating instructions • SpotClip-Plate • 09-2017 • 009-50104

2 Safety instructions

The products are manufactured in accordance with the
current state of technology and the recognised safety
regulations. Nevertheless, improper use of the products
can result in hazards to life and limb of the user or third
parties or damage to the products and other material
assets. These operating instructions contain information
on safety.
f Always follow all of the instructions to prevent personal
injury, material damage or environmental damage.
2 .1 Representation and layout of warning
instructions
The warning instructions relate to actions and are
structured as follows:
WARNING
Type and source of danger!
Explanations on the type and source of danger.
f Measures to prevent danger.
A warning indicates possible risk of lethal or serious
injuries.

2 .2 Limitations of use

f Observe the following requirements for the operational
environment:
• The products can only be used for LED lights and
fluorescent lamps.
• They can be used for ceiling cut-outs from 75 mm to
314 mm.
• They can be used with insulating material in solid form.
Do not use loose-fill insulating materials.

3 User obligations

The user must observe and comply with the respectively
applicable national Building, Safety, Health and
Environmental regulations. Use of the products does not
exempt the user from complying with the installation
instructions provided by the manufacturer of the
recessed lights. Please contact a specialist if you have
any questions.

4 Transport and storage

Do not stack heavy objects on the packaged products.