Hitachi CS 36DL Mode D'emploi page 14

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 39
English
4. When visibility is poor, such as during bad weather or
night, do not use the unit. In addition, do not use it in rain
or in a location exposed to rain.
Unstable foothold or loss of balance may result in an
accident.
5. Check the guide bar and saw chain before starting the
unit.
○ If the guide bar or saw chain is cracked, or the product
is scratched or bent, do not use the unit.
○ Check if the guide bar and saw chain are securely
installed. If the guide bar or saw chain is broken or
dislodged, this may result in an accident.
6. Before starting work, check to ensure the switch does
not engage unless the lock-off button is pressed.
If the unit does not working properly, immediately stop
using and request repair from your Hitachi Authorized
Service Center.
7. Install the saw chain properly, in accordance with the
instruction manual.
If installed incorrectly, the saw chain will come off the
guide bar and injury may occur.
8. Never remove any of the safety devices equipped
on the chain saw (brake lever, lock-off button, chain
catcher etc.).
In addition, do not alter or immobilize them.
Injury may occur.
9. In the following cases, switch the unit off and ensure the
saw chain is no longer moving:
○ When not in use or being repaired.
○ When shifting to a new work location.
○ When inspecting, adjusting or replacing the saw chain,
guide bar, chain case and any other part.
○ When refi lling the chain oil.
○ When removing dust etc. from the body.
○ When removing obstacles, trash or sawdust generated
from work from the work area.
○ When you take off the unit, or when you get away from
the unit.
○ Otherwise, if you sense danger or anticipate risk.
If the saw chain is still moving, an accident may occur.
10. Work should generally be performed individually. When
multiple individuals are involved, ensure suffi cient
spacing between them.
In particular, when felling standing trees or working on
a slope, if you anticipate trees falling, rolling or sliding,
ensure there is no danger to other workers.
11. Remain more than 15 m away from other people.
In addition, when working with multiple persons, remain
15 m or more apart.
○ There is a risk of impact with scatters and other accidents.
○ Prepare a whistle alert etc. and determine appropriate
contact method for other workers beforehand.
12. Before felling standing trees, ensure the following:
○ Determine a safe evacuation location prior to felling.
○ Remove obstacles (e.g., branches, shrubs) in advance.
○ Based on a comprehensive evaluation of the state of the
tree to be felled (e.g., trunk bend, tension of branches)
and the surrounding situation (e.g., state of adjacent
trees, presence of obstacles, terrain, wind), decide on
the direction in which the standing tree will fall and then
plan the felling procedure.
Careless felling may result in injury.
13. When felling standing trees, ensure the following:
○ During work, be very careful of the direction in which
trees fall.
○ When working on a slope, ensuring the tree will not roll,
always work from the uphill side of the terrain.
○ When the tree starts falling, switch the unit off , alert
the surroundings, and immediately retreat to a safe
location.
14
○ During work, if the saw chain or guide bar become
entangled in the tree, switch off and use a wedge.
14. During use, if the unit performance deteriorates, or you
notice any abnormal sound or vibration, immediately
switch off and discontinue use, and return to your
Hitachi Authorized Service Center for inspection or
repair.
If you continue using, injury may occur.
15. If the unit is accidentally dropped or exposed to impact,
inspect carefully for damage or cracks and ensure there
is no deformation.
If the unit is damaged, cracked or deformed, injury may
occur.
16. When transporting the unit by car, secure the unit to
prevent it moving.
There is a risk of accident.
17. Do not switch the unit on while the chain case is
attached.
Injury may occur.
18. Ensure there are no nails and other foreign objects in
the material.
If the saw chain impact on the nail etc., injury may occur.
19. To avoid the guide bar becoming entangled with the
material when chopping on a verge or when subject to
the weight of material while cutting, install a supporting
platform close to the cutting position.
If the guide bar becomes entangled, injury may occur.
20. If the unit is to be transported or stored after use, either
remove the saw chain, or attach the chain cover.
If the saw chain comes into contact with your body,
injury may occur.
21. Adequately care for the unit.
○ To ensure work can be performed safely and effi ciently,
care for the saw chain to ensure it provides optimal
cutting performance.
○ When replacing the saw chain or guide bar, maintaining
the body, fi lling oil etc., follow the instruction manual.
22. Ask the shop to repair the unit.
○ Do not modify this product, since it already complies
with the applicable safety standards.
○ Always refer to your Hitachi Authorized Service Center
for all repairs.
Attempting to repair the unit yourself may result in an
accident or injury.
23. When not using the unit, ensure it is properly stored.
Drain off the chain oil, and keep in a dry place out of
reach of children or a locked location.
24. If the warning label is no longer visible, peels off or is
otherwise unclear, apply a new warning label.
For the warning label, refer to your Hitachi Authorized
Service Center.
25. When working, if local rules or regulations apply,
comply with the same.
PRECAUTIONS FOR BATTERY AND CHARGER
1. Always charge the battery at a temperature of 0°C –
40°C. Charging the battery at temperatures outside the
range of 0°C – 40°C may prevent proper charging and
reduce battery life.
The most suitable temperature for charging is that of
20°C – 25°C.
2. When one charging is completed, leave the charger for
about 15 minutes before the next charging of battery.
Do not charge the battery more than 2 hours.
3. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
4. Never disassemble the rechargeable battery and
charger.

Publicité

Table des Matières
loading

Table des Matières