B For Machines Driven By Cardan Shaft (Celtis 100 Gc - Celtis 100 Gc+T); C For Machines With Premium Graded Fuel Engine (Celtis 100 B&S); Lighting; Use - Bell PICKPINE CELTIS 100 E Livret D'emploi Et D'entretien

4.3.B - For machines driven by cardan shaft (CELTIS 100 GC - CELTIS 100 GC+T)
•
Make sure the tractor is off, that the parking brake is on and if necessary that the wheels are chocked.
•
Connect the log splitter to the three points of the tractor.
•
Connect the cardan shaft to the gearbox (fig.7, page 2) to the power take-off of the tractor. The cardan shaft must be of suitable length and
complete with protective cover. Check that it clicks into place.
•
After connecting the log splitter, start the tractor and check that the cardan shaft turns in the direction indicated on the data plate on the gearbox
(see par. 1.1 "SYMBOLS USED" on page 20).
•
Position the accelerator at a suitable rpm for your tractor so that the engine provides sufficient power for correct functioning of the log splitter and
check that the power take-off does not exceed 540 rpm as shown on the data plate (see par. 1.1 "SYMBOLS USED" on page 20)
WARNING
Follow the few very important rules indicated above to avoid problems that could cause injury or damage.
WARNING
Never touch the cardan shaft or any other rotating parts. This is extremely dangerous and may cause injury or damage.
4.3.C - For machines with premium graded fuel engine (CELTIS 100 B&S)
•
Before operating the log splitter, carefully read the user's manual for the engine fitted. study the maintenance regulations and guarantee supplied.
•
Check the oil level in the engine block. top up if necessary.
WARNING: working without oil causes irreparable damage.
•
When the engine is new, it is important, at first start-up, to let it turn over without performing any work for at least twenty minutes.
This running-in period ensures maximum performance and smooth operation of the whole system.

4.4 - Lighting

Lighting must be provided in the entire work area of the log splitter to ensure perfect visibility when operating the machine and during maintenance and
adjustments. Even when working outdoors, there must be sufficient light to work safely. Working at times when insufficient light may result in poor visibility
of the machine and its components (dawn, dusk, night) is forbidden.

5 - USE

WARNING:
Do not use the machine outdoor when it is raining or snowing.
When not in use, store the machine where it is protected from atmospheric agents.
5.1.A - Switching on/off of the machine with electric motor (CELTIS 100 E - CELTIS 100 T - CELTIS 100 GC+T)
•
Make sure that the switch/cutout of the general power system and the switch of the machine are OFF.
•
Connect the electric log splitter to the power system inserting the plug in the socket on the electric motor.
•
Never pass the power cable over the telescopic mast, close to the wedge or anywhere where it may be damaged or cut.
•
Set the main on/off switch and then press the switch in the green area to start the log splitter.
The telescopic mast will move automatically to the fully open position.
•
Use the log splitter as explained in paragraph 5.2.
•
Never leave the log splitter unattended without first of all pressing the switch in the red area (off).
•
On completing the work, switch off the log splitter by turning the switch/differential of the general power system to the "0" position (off) and then
remove the plug from the socket on the machine. Never yank the plug using the cable. Grasp the body of the plug and pull it firmly.
5.1.B - Switching on/off of the machine driven by cardan shaft (CELTIS 100 GC - CELTIS 100 GC+T)
•
Connect the log splitter to the power source (see chapter 4 "OPERATING THE MACHINE") and then check that the machine is firmly positioned on
the ground.
•
Start the tractor making sure it does not move. Start the log splitter by activating the power system (cardan shaft). The wedge will lift.
•
Use the log splitter as explained in paragraph 5.2.
•
If you leave the log splitter unattended, switch off the transmission system of the tractor.
•
After using the log splitter, switch off the transmission system, switch off the tractor. Before moving the tractor, lift the log splitter to a sufficient
height so that it does not hit the ground.
WARNING
Never move the tractor with the power source of the log splitter activated or with the log splitter still on the ground.
24
ENGLISH
D22031470 - v.2 - UPD 291209