Fontanot GENIUS 010 Q Instructions De Montage page 8

Fixing landing
16. Move component 047009 towards ceiling. Determine the position, keeping a distance of about 15 cm from the
outer edge of the landing, drill with a 14 mm bit and definitively secure, using components 008001 (Fig. 1) (Fig. 2).
17. Fix components 047009 to landing, using components 011053 (drill landing with a 4.5 mm bit).
18. Position components 132016 (Fig. 1) (Fig. 2).
Assembly of 010 railing (go to point 35 for model 020)
19. Starting from the top, fit balusters 127010, with parts 033142 and 002040, onto corner treads with a height of
about 97.5 cm.
20. Cut sections of handrail 140010 to length; assemble with part 046011. For optimal fixing, the handrail must follow
about 1/8 of a turn from the contact point.
21. Fix handrail to balusters with parts 002031; keep balusters vertical. Insert angle parts 033103, 033105 and
033107 with screws 012014 and 001017 for changes of direction. Apply end caps 033103 to ends of handrail with
parts 011069 and 004034, drill with a 6 mm bit (Fig. 1) (Fig. 11).
22. Position the first 127010 baluster; adjust the height according to the balusters already mounted. Fix component
033142 to the floor using a Ø 8 mm bit, so that it corresponds with the first baluster. Use elements 011053,
008004, and 001004 (Fig. 1).
23. Cut a piece of baluster 127012 to length to obtain spacers to connect treads; lock in place with parts 001010.
24. Definitively tighten component 005008 (Fig. 5).
25. Insert the steel cables into the 034041 parts on the banisters, positioning parts 031098 and 001012 on each end
of the banisters and on one intermediate baluster positioned between the two ends of the banister side. Fasten
the cables at one of the two ends using parts 031098 and 001012, leaving about 15mm protruding from parts
034041; cover with articles 034042 and 001012. Tighten the cables by hand and lock parts 031098 and 001012
respectively working from the lower to the higher end of the steel cable. Once the final parts 031098 and 001012
have been fastened, cover the ends of the cables with adhesive tape to prevent them from unravelling whilst being
cut. Cut the cables at a distance of 15 mm from parts 034041. Remove the tape and cover with articles 034042
and 001012 (Fig. 1) (Fig. 11).
26. Complete assembly of accessories, fitting components BF2 into the lower part of balusters 127010 on corner
treads and into upper part of lateral spacers 127012 (Fig. 1) (Fig. 11).
Assembly of 010 balustrade
27. Screw part 033063 onto stay 046036 with screw 011038 (Fig. 1).
28. Position components 033063 on landing, using components 002040 and 001004. Drill landing with a 5 mm bit,
keeping a distance between centres that allows at least four balusters to be fitted.
29. Position balusters 127014, with components 033078 facing outwards, and tighten component 001004 (Fig. 1).
30. Fix straight handrail 140010 using components 002031 (Fig. 1).
31. Depending on position and presence of walls around the stairwell, it may be necessary to position one or two extra
balusters 127014.
32. In this case, a space must be considered that is at the same distance from the other balusters or from the wall.
Drill landing with a 4.5 mm bit and assemble with components 033063, 001004 and 002040 (Fig. 1).
33.  A ssemblyoffloor-mountedbalustrade,ifapplicable(Fig.13)
Determine the position of the posts on the floor, on average one every 28 cm and at a distanza of 8 cm from the
edge. Drill with a Ø 10 mm bit and insert the 046015 components, fixing them with chemical resin (not supplied).
Assemble components 033063 with components 009002 and 005001. Insert the 127014 balustrade balusters
(H= 910 mm) into the 033063 components, with the 126034 reinforcing baluster about every metre, and lock them
with components 001004. Fix the balusters to the wall using component 033010 and items 008004, 011053 and
033056 (drill with an Ø 8 mm bit). Determine the length of the handrails and cut off the excess quantity. Assemble
the 140010 handrails to the balusters with the 002031 components using item 046011. Assemble any 033103,
033105, 033107 connecting components and the 033103 terminal components.
34. Insert the steel cables into the 034041 parts on the banisters, positioning parts 031098 and 001012 on each end
baluster of the banisters and also on one intermediate baluster positioned between the two ends of the banister
side. Fasten the cables at one of the two ends using parts 031098 and 001012, leaving about 15mm protruding
from parts 034041; cover with parts 034042 and 001011. Tighten the cables by hand and lock parts 031098 and
001012 respectively working from the lower to the higher end of the steel cable. Once the final parts 031098 and
001012 have been fastened, cover the ends of the cables with adhesive tape to prevent them from unravelling
whilst being cut. Cut the cables at a distance of 15 mm from parts 034041. Remove the tape and cover with parts
034042 and 001011 (Fig. 1 - 11).
8 - Genius 010 - 020 Q