SOMFY OXIMO 40 AUTO io Notice page 11

ORIGINAL INSTRUCTIONS
These instructions apply to all versions of the OXIMO 40 AUTO io (torque/speed).
CONTENTS
1. Prerequisite information 21
1.1 Field of application 21
1.2 Liability 22
1.3 Content 22
2. Installation 22
2.1. Assembly 22
2.2. Wiring 24
2.3. Commissioning 24
2.4. Tips and recommendations
for installation 26
The OXIMO 40 AUTO io drive automatically programs its end limits.
The OXIMO 40 AUTO io drive can be mounted either on the right or on the left.
obstacle protection to protect the roller shutter when it is being lowered.
-
- anti-freeze protection to protect the roller shutter when it is being raised.
1. PREREQUISITE INFORMATION
1.1 FIELD OF APPLICATION
The Oximo 40 Auto drive is designed to motorise all types of roller blinds equipped with stops and
- The motorised product is controlled by a switch without a locking device (see the attached Safety
instructions document).
- When deployed, all parts of the motorised product are more than 2.50 m above ground or any other
permanent access level.
slat placed 16 cm from its fully-deployed position.
If the roller shutter has slats which can open, the openings must not allow a pin of diameter 5 mm
to pass through.
Copyright © 2014 Somfy SAS. All rights reserved.
EN
3. Use and maintenance 28
3.1. Up and Down buttons 28
3.2. STOP function 28
3.3. Favourite position (my) 28
3.4. Operating with a Somfy
io-homecontrol sun sensor 28
3.5. Additional settings 28
3.6. Tips and recommendations for use 29
4. Technical data 29
21
Images not contractually binding
EN
1.2 LIABILITY
Please read these instructions carefully before installing and using the OXIMO 40 AUTO drive. In
addition to following the instructions given in this guide, the instructions detailed in the attached
Safety instructions document must also be observed.
The OXIMO 40 AUTO io drive must be installed by a motorisation and home automation
professional, according to instructions from Somfy and the regulations applicable in the
country in which it is commissioned.
Such use, and any failure to comply with the instructions given in this guide and in the attached
Safety instructions document, absolves Somfy of any liability and invalidates the warranty.
Installers must inform their customers of the operating and maintenance conditions for the OXIMO
40 AUTO io drive and must provide them with the instructions for use and maintenance, and the
attached Safety instructions document, after installing the OXIMO 40 AUTO io drive. Any After-Sales
Service operation on the OXIMO 40 AUTO io drive must be performed by a motorisation and home
automation professional.
If in doubt when installing the OXIMO 40 AUTO io drive, or to obtain additional information, contact
a Somfy adviser or go to the website www.somfy.com.
1.3. CONTENTS
The OXIMO 40 AUTO io drive comprises two inseparable
- the drive part (A)
the electronic part (B)
-
Safety warning! Caution!
2. INSTALLATION
Instructions which must be followed by the motorisation and home automation professional
installing the OXIMO 40 AUTO drive.
Never drop, knock, drill or submerge the drive.
Install a separate control point for each drive.
2.1. ASSEMBLY
It is essential to follow the order of assembly given in the instructions
2.1.1. Preparing the drive part
The drive part must always be installed before the electronic part.
Check that the inner diameter of the tube is 37 mm or greater.
1) Fit the accessories required to integrate the drive in the
2) Measure the length (L1) between the inner edge of the drive
head and the rim of the drive wheel.
22
Images not contractually binding
B
A
V
Information Up Down
1)
Ø = 37 mm
Ø > 37 mm
a b c
2)
L1 = ...
L1
Copyright © 2014 Somfy SAS. All rights reserved.