Intended Use - Express 2010 Instructions D'emploi

EN Operating Instructions
etc in accordance with these instructions and
in the manner that is prescribed for this special
device type. Take the working conditions and the
activity that is to be performed into consideration
while doing this. The use of electrical tools for
other applications than those that are intended
can result in dangerous situations
Prior to cleaning: Switch off mains! Use a mild
cleaning agent and a damp cloth for cleaning.
Never clean devices so they are dripping wet!
Service
Never have your device repaired by anyone
but qualified personnel and always use original
spare parts. This will ensure that the safety of the
device is maintained.
Only authorized personnel should exchange
fuses or perform repairs. Please contact the ad-
dress shown below.

Intended Use

This hot air device is intended for all the hot
air applications listed in this operating manual;
always observe the safety regulations and only
use original accessories with it.
Applications A:
· Welding of thermoplastics and elastomere
bitumen
· Shrinking of heat-shrinkable tubing, foil packag-
ing
· Warming up thermoplastic semi-finished goods
for purpose of forming
· Drying of watery wet surfaces
· Unthawing of frozen water pipes
· Removing old shellac varnish, synthetic enamel
· Activating and dissolving adhesives and hot-
melt type adhesives which do not contain any
solvents
Applications B:
· Industrial assembly work
· Drying and heating up processes of all kinds
· Activating and dissolving adhesives and hot-
melt type adhesives which do not contain any
solvents
· Heat-shrinking and welding of foil packaging
and preforms
· Separating and fusing together synthetic
threads and textiles
12
· Sterilizing packaging materials
· Removing plastic flashing and finish-polishing
plastic surfaces
The device is not suitable to be used in an explo-
sive atmosphere!
Touching hot jets or reflectors can lead to seri-
ous burns. Before assembling or changing jets
or reflections, allow the device to cool down
completely or use suitable tools. The jets and
reflectors must be mounted firmly and safely
onto the device.
Hot jets and reflectors can ignite items or the
base of the device. Always ensure you only set
down hot jets and reflectors on a fire-resistant
base.
Incorrect or damaged jets can cause a block-
age of hot air and damage the device. Use only
original jets or reflectors!
Device elements:
1. Heating element pipe
2. Rubber stand
3. Handle
4. Mains connection lead
5. Mains outlet
6. Potentiometer for setting temperature
7. Flexible guard sleeve
8. Filter
Mounting and firm installation:
Mounting and firm installation:
The device is intended for installation in machin-
ery and equipment and is designed for continu-
ous operation.
Please ensure the following points when install-
ing:
· that only cold air is supplied
· that no heat blockage can develop
· that the device is protected against mechanical
vibrations and jarring
· that other sources of hot air do not blow on the
device
Commissioning:
Check mains connection lead and plug for me-
chanical damages!
Observe the mains voltage! The mains voltage
must coincide with the details on the rating plate.
Activation:
Set the mains switch 5 to position 1. Adjust the
temperature using the potentiometer 6, if neces-
sary. The warm-up time for the device is approx
5 minutes.
De-activation:
Turn the potentiometer 6 to position 0 for cooling
down. Once the unit has cooled down, set the
switch 5 to 0.
Maintenance, service and repairs:
Check mains connection lead and plug for
breaks and mechanical damages!
Before commencing with any work on the device,
disconnect the mains plug!
Always keep the device and air intake screens
clean. If necessary, clean the dirty screens with
a brush while the device is switched off. Only
original accessories may be used.
Once the carbon brushes reach the minimum
length, the fan motor will switch off automatically.
Have the carbon brushes replaced by an autho-
rised service centre or a specialist company.
Repairs on the device should only be performed
by an authorized repair shop.
Technical Data:
Nominal voltage 120 V or 230 V~
range:
Frequency range: 50Hz - 60Hz
Output: 120 V 1650 W or 230 V
1500 W
Output temperature: ≤ 700°C
Noise emission level: < 70dB
Protection class:
II / (double insulated)
Weight: 1.4 kg including mains
connection lead
Disposal
Do not dispose of in the household trash.
Add the device that is no longer able to be
used to a separate collection for the pur-
pose of environmentally friendly recycling.
Operating Instructions EN
Help in the event of problems:
Guilbert Express
33 avenue du Maréchal de Lattre de Tassigny
F-94127 FONTENAY-SOUS-BOIS CEDEX
Tel.: +33 (0)825 800 251
info@express.fr
www.express.fr
EU Declaration of Conformity
Guilbert Express
33 avenue du Maréchal de Lattre de Tassigny
F-94127 FONTENAY-SOUS-BOIS CEDEX
hereby declares that the product
Equipment type: Hot air fan
Model name: Type 2010
agrees with the requirements of the following
European Directives:
EU Directive 2006/42/EU - NSR
EU Directive 2014/30/EU - EMC
EU Directive 2014/35/EU
2011/65/EU ROHS-2
The concurrence of the specified product with
the requirements of Directive 2006/42/EU is
proven by the observance of the following stan-
dards:
EN 60335-1:2002 + A11:2004 + A1:2004 +
A12:2006 + Corrigendum:2006 + A2:2006
EN 60335-2-45:2002
EN 50581-2012
the last two digits of the year in which the CE
marking was attached: 17
The concurrence of the specified product with
the requirements of Directive 2014/30/EU is
proven by the observance of the following stan-
dards:
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 60335-2-45:2002
13