Assembly And Operation - HERKULES KGZ 3300 Mode D'emploi

Anleitung KGZ 3300 Herkules
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine's moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
Important:
This machine was exactly adjusted before it left the
factory. For the best results you should check the
accuracy of the following settings and make
corrections as necessary.
6.1 Setting the angle stop to 90° and 45° (Fig.
5/6/7)
Release the angle clamping lever (13) and move
the cutting head (4) all the way to the right.
Secure the angle clamping lever (13).
Use an angular stop (a/b) to set the blade at 90°
in relation to the table.
If an adjustment is necessary, undo the locknut
(d) and turn the screw (c) so that the blade
makes an angle of 90° with the table.
Tighten the locknut (d).
Use the screw (c) to set the angle indicator (15)
to 0.
Use the same procedure to set the stop to 45°,
but instead move the cutting head to the left and
use the left screw (e).
6.2 Setting the stop face (Fig. 12)
Lower the cutting head and press in the locking
button (16). Make sure that the table shows a
miter angle of 0°.
Place an angular stop against the stop face and
the saw blade.
If the blade does not touch the angular stop,
undo the three screws (33).
Adjust the stop face so that it touches the angle
gage full-face. Retighten the screws.

7. Assembly and operation

Always place the workpiece against the stop face. A
twisted and bent workpiece that cannot be held flat
on the table or against the stop face may catch on
the blade and should not be used. Keep your hands
out of the sawing zone. The entire table area is out of
bounds for hands. It is marked with "No Hands"
signs.
19.08.2004 10:31 Uhr Seite 15
7.1 Fitting the clamping device and extension
supports (Fig. 1/3/4)
Always use the clamping device (19) to secure
the workpiece in position. Insert the clamping
device in one of the mounts (30) provided and
fasten it in place with the clamping screw.
Insert the extension supports on the left and right
in the mounts (29) provided in the base plate
and tighten the clamping screw.
The standard end stop (18) can be used for
repeat cuts. In this case, slip the end stop onto
one of the extension supports and adjust with the
clamping screw.
7.2 Fitting the dust extraction device (Fig. 11/12)
Mount the dust extraction nozzle (28) in the outlet
opening under the cutting arm.
Mount the big end of the angle piece (35) on the
back of the crosscut and miter saw at the outlet
opening. The angle piece has to point to the side
or down.
On the angle piece you can either attach the dust
bag (24) or a suction hose for drawing off the saw
dust.
Mount the second angle piece on the upper dust
extraction socket (34) and plug on the suction
hose (26).
With the Y-piece (27) you can join together the
upper and lower suction hose and connect them
to a suitable vacuum extraction system.
7.3 Setting up the saw unit (Fig. 1/2)
To adjust the turntable (8), loosen the locking grip
(10) by approx. 2 turns, which frees the turntable (8).
Turn the turntable (8) and scale pointer (11) to
the desired angular setting on the dial (12) and lock
into place with the locking grip (10).
To release the saw from its position at the bottom
(transport position), pull the retaining pin (16) out of
the motor mounting while pressing down lightly on
the machine head (4).
Swing the machine head (4) up until the retaining
hook latches into place.
When the tightening screw (13) is loosened, you
can tilt the machine head (4) to the left by up to 45°.
Warning!
Never connect the plug to a power source before
you have completed all the installation work,
made all the necessary settings, and read and
understood all the safety and operating
instructions.
7.4 Crosscut 90° and turntable 0° (Fig. 8)
For cutting widths up to 170 mm it is possible to fix
the saw's drag function with the thumb screw (14) in
GB
15