Garmin REACTOR 40 KICKER YAMAHA EFI Instructions D'installation page 3

4
Assemble the parts in this adapter kit and secure them to the
motor (Throttle Actuator Component Connections, page
5 Using the Reactor 40 Kicker Throttle Actuator Installation
Instructions , complete and test the throttle actuator
installation.
Assembling the Throttle Linkage
The throttle linkage allows the throttle cable from the actuator to
pull open the throttle lever on the motor.
1
Using the parts provided in this adapter kit, place the throttle
linkage bracket on the tapered end of the throttle linkage
arm .
2
Using the bolt and nut provided in this adapter kit, fasten the
bracket to the arm.
3
Tighten the nut so the bracket is securely connected to the
arm, but loose enough so the bracket moves freely.
Connecting the Throttle Actuator Cable to the Throttle
Linkage
The throttle linkage is designed to hold the cable from the
throttle actuator securely. Because of the design, you must
connect the throttle actuator cable to the throttle linkage before
you secure the parts to the motor.
1
If necessary, assemble the throttle linkage
Throttle Linkage, page
2
Place the round end of the throttle actuator cable into the
hole on the end of the throttle linkage.
3
Rotate the cable so it feeds through the slot on the end of the
linkage.
Throttle Actuator Component Connections
Part Notes
You should connect the throttle actuator cable to the
throttle control linkage
Throttle
actuator cable
throttle cable bracket
(from the
Actuator Cable to the Throttle Linkage, page
throttle actuator
box)
You must secure the throttle actuator cable
throttle cable bracket using the included screws
Throttle cable
(Securing the Throttle Actuator Cable to the Bracket,
bracket
page 3).
Installation Instructions
(Assembling the
3).
before securing it to the
(Connecting the Throttle
Part
3).
Manifold
mounting
location
Throttle control
linkage
Securing the Throttle Actuator Cable to the Bracket
Before securing the cable to the bracket, you should connect the
end of the throttle actuator cable to the throttle linkage
(Connecting the Throttle Actuator Cable to the Throttle Linkage,
page 3).
1
Place the top of the bracket
throttle actuator cable
2
Secure the cable to the bracket using the included screws
Securing the Throttle Control Linkage to the Throttle
Control Wheel
You must assemble the throttle control linkage before installing it
(Assembling the Throttle Linkage, page
1
Taking care that it does not fall into the motor housing,
remove the 10 mm nut
wheel and spring
down the throttle shaft.
NOTE: You must use extreme care when removing the nut
on the bottom of the throttle control wheel and spring. If the
spring drops down and falls off of the throttle shaft, it can
unwind and may be difficult to reinstall.
2
Apply a humidity-cured, ethyl-based thread-locking
compound, such as LOCTITE 435, to the threads on the
3).
throttle shaft and to the 10 mm nut you removed in the first
step.
to the
Vibration from normal use may result in this nut falling off if
you do not apply a thread-locking compound.
Notes
You must remove the existing bolt on the manifold
and use it to secure the throttle cable bracket
You must assemble the throttle control linkage before
installing it (Assembling the Throttle Linkage, page
You must use extreme care when removing the nut
on the bottom of the throttle control wheel and spring.
If the spring falls off, it can unwind and may be
difficult to reinstall (Securing the Throttle Control
Linkage to the Throttle Control Wheel, page
over the raised portion of the
.
3).
at the bottom of the throttle control
, and hold the spring so it does not slide
NOTICE
.
3).
3).
.
3