Royal Catering RCEF 16DH-1 Manuel D'utilisation page 5

EN
Ensure good ventilation in the room in which the device is
used The distance between the back of the chain toaster
and the wall should be at least 20 cm, a minimum distance
between the sides of the device and the walls should be
at least 10 cm on each side and 35 cm between the top
of the device and the ceiling. Keep the device away from
hot surfaces. Operate the device on flat, stable, clean,
refractory and dry surfaces out of the reach of children and
people with mental disabilities. Install the device making
sure that constant access to the main plug is ensured. The
power cord connected to the appliance must be properly
grounded and correspond to the technical details. Before
the first use, remove all elements and clean them along
with the entire device.
PRINCIPLE OF OPERATION
4
5 6
5
4
6
7 8
9
7 8 9
3
3
2
1
2
1
1. tap with release valve
2. handle with basket
3. lid
4. RESET button (at the back of the device)
5. power cable at the back of the device)
6. thermostat
7. thermostat light
8. power light
9. ON / OFF switch
10. earth (at the back of the device)
ATTENTION! The RCEF 16DH-1 model is shown in the
photograph. The 10EH-1 is a single model – all buttons
and functions are the same as for the RCEF 16DH-1 model.
1. Fill the tanks with oil so that level is between the
marks of minimum and maximum level.
2. Set the thermostat to „0" and insert the plug into an
electricity socket.
3. Use the ON/OFF switch to turn the device on (the
RCEF 16DH-1 model has separate switches for each
basket). The green light will come on. Then select
the required temperature (in a clockwise direction);
the orange light will come on and the heating
element will begin heating up. Once the required
temperature has been reached, the heating orange
light will go off. The thermostat will maintain the
required temperature by automatically switching
the heating element on and off. This maintains the
required temperature and saves electricity. You may
begin frying.
4. Use the baskets after mounting the handles. Place
food in the basket and immerse it into the oil. When
the food is tried, hang the basket up on the nail to
let the oil drop off.
8
5. The covers are designed to keep the content warm
and t protect it from dirt. If you want to use the
covers, make sure they are not wet.
6. When you have finished working, tilt the heating
elements 90 degrees backwards. The heating
elements are vertical, and the oil can drop off.
7. Use the ON / OFF switches to turn the device on.
8. Our fryers are equipped with a safety button.
When the heating element is tilted back, it turns
automatically to prevent from accidents.
9. Once the oil cools down to room temperature,
discharge it using the release valve.
10. Make sure the thermostat is back to „0" (adjust
the thermostat knob anticlockwise) when you have
finished your work and disconnect the fryer.
11. It is recommended to use only liquid oil or fat in the
fryer to avoid damages of the temperature limiter.
It is not recommended to put block fat in the fryer
– block fat should be melted before putting it into
the fryer.
ATTENTION! The device has a sensor to prevent it
from overheating. If the device overheats when in
use it will automatically switch off. Then wait approx.
15 minutes, unscrew the cap which protects the reset
button, press RESET and screw the protective cap
back on. The device may be used again.
ATTACHING THE HANDLE TO THE BASKET
10
TRANSPORTATION AND STORAGE
During transport, the machine should be protected from
shaking, falling and turning upside down. Store it in
a properly ventilated place with dry air and without any
corrosive gas.
CLEANING AND MAINTENANCE
• Always unplug the device before cleaning it and after
each use.
• Discharge oil and remove heating element.
• Use a damp cloth suitable for cleaning devices or use
natural vinegar suitable for food grade equipment.
• Do not use water to wash the electric control panel
as this might cause damage and invalidate the
warranty.
• Use cleaner without corrosive substances to clean
surface.
• After cleaning the device, all parts should be dried
before reusing it.
• Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
CHECK REGULARLY THE DEVICE
Regularly check the machine for signs of damage. If the
machine is damaged, please stop using it immediately and
contact your customer service to solve the problem.
Rev. 14.02.2022
What to do in case of a problem? Please contact your
customer service and prepare the following information:
• Invoice number and serial number (the latter is to be
found on the technical plate on the device).
• If relevant, take a picture of the damaged, broken or
defective part.
• It will be easier for your customer service clerk to
determine the source of the problem if you give
a detailed and precise description of the matter. The
more detailed your information, the better customer
service will be able to solve your problem rapidly and
efficiently!
CAUTION: Never open the device without the authorization
of your customer service. This can lead to a loss of warranty!
Rev. 14.02.2022
EN
9