Attach Mounting Plate To Wall; Prepare Upper Cabinet - IKEA LAGAN AA-2126135-1 Instructions D'installation

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Attach Mounting Plate to Wall

NOTE: Secure the mounting plate to the wall at both end
holes drilled into the wall studs and/or drywall using either
3/16-24 x 3" round-head bolts and toggle nuts or 1/4 x 2"
lag screws.
Refer to illustrations in "Possible Wall Stud Configurations"
in the "Locate Wall Stud(s)" section.
No Wall Studs at End Holes (Figures 1 and 2)
NOTE: The mounting plate must be secured to the wall
on at least 1 wall stud as well as at both ends.
1. With the support tabs of the mounting plate facing forward,
insert 3/16-24 x 3" round-head bolts through both end holes
of mounting plate.
2. Start toggle nuts on bolts from the back of the mounting
plate. Leave enough space for the toggle nuts to go
through the wall and to open.
A
A. 3/16-24 x 3" round-head bolt
B. Mounting plate
C. Spring toggle nut
3. Position mounting plate on the wall.
4. Push the 2 bolts with toggle nuts through the drywall
and finger tighten the bolts to make sure toggle nuts
have opened against drywall.
A
B
A. 3/16-24 x 3" round-head bolt
B. Mounting plate
C. Spring toggle nut
D. Drywall
5. Insert lag screw(s) into the hole(s) drilled into wall stud(s)
in Step 2 of "Installation for No Wall Studs at End Holes"
in the "Drill Holes in Rear Wall" section.
6. Check alignment of mounting plate, making sure it is level.
7. Securely tighten all lag screws and bolts.
B
C
C
D
Wall Stud at One End Hole (Figure 3)
1. With the support tabs of the mounting plate facing forward,
insert a 3/16-24 x 3" round-head bolt through the end
hole that fits over the 5/8" (16 mm) hole drilled in Step 3
of "Installation for Wall Stud at One End Hole" in the "Drill
Holes in Rear Wall" section.
2. Start a toggle nut on the bolt from the back of the mounting
plate. Leave enough space for the toggle nut to go through
the wall and to open.
3. Position mounting plate on the wall.
4. Push the bolt with toggle nut through the drywall and
finger tighten the bolt to make sure toggle nut has opened
against drywall.
5. Insert a lag screw into the remaining end hole.
6. If installing on a second wall stud, insert a lag screw into
the other hole drilled in Step 2 of "Installation for Wall Stud
at One End Hole" in the "Drill Holes in Rear Wall" section.
7. Check alignment of mounting plate, making sure it is level.
8. Securely tighten the lag screw(s) and bolt.
Wall Studs at Both End Holes (Figure 4)
1. Position mounting plate on the wall.
2. Insert lag screws into both end holes.
3. Check alignment of mounting plate, making sure it is level.
4. Securely tighten the lag screws.

Prepare Upper Cabinet

1. Disconnect power to outlet.
2. Remove all contents from upper cabinet.
3. Place upper cabinet template against the bottom of
the upper cabinet and attach with tape or thumbtacks.
Make sure the template centerline aligns with the vertical
centerline on the rear wall.
The "rear wall" arrows must be against the rear wall so that
the holes cut into the upper cabinet align with the holes in
the top of the microwave oven.
NOTES:
If the upper cabinet has a frame around it, trim the template
edges so that it fits inside the frame, against the upper
cabinet bottom. The template has trim lines to use as guides.
If the wall behind the microwave oven (as installed) has
a partial wall covering (for example, tile backsplash), be
sure the "rear wall" arrows align to the thickest part of
the rear wall (for example, the thickness of the tiles rather
than the drywall).
4. Make sure the 10" (25.4 cm) dimension from the rear wall
to points "D" and "E" on the template is maintained.
U p
p e r
D
10"
(25.4 cm)
e
- c a b i ne t t e m p l
a t
E
10"
G
(25.4 cm)
F
9

Publicité

Table des Matières
loading

Table des Matières