Description; Technical Details; Front Wheel Assembly; Assembly - Eurosystems Asso 71 Notice D'instructions Et Mode D'emploi

G
B
1 Seat
2 Steering wheel
3
4 Blade
5 Ignition key
Engine
Electric starter
Advance
Maximun speed
Dimensions
Body
Cutting plate
Cutting width
Cutting height regulation
Curvature radius
Tyres
front
rear
Weight
Assembled with
Noise level (LWA)
Measured according to directives 85/538 EWG 88/180 EWG - 87/252 EWG
1. Mount the front wheels on the pins (1), positioning a washer (2), the wheel (3) and 2
washers (4).
2. Secure with a stop (5).
UNPACKING/ ASSEMBLY
The ride-on-mower is packed in a carton and is ready assembled apart from the steering
wheel, seat, grass collection bin and front wheels. Please observe the following sequence
when unpacking the machine:
1. Unpack all the parts that have been delivered. Dispose of the carton and pallet in an
environmentally friendly way.
2. Check all the parts
3. Begin assembly.
It is strictly forbidden to start the ride-on-mower (even for trial purposes) without
completing assembly.
STEERING WHEEL ASSEMBLY
1. Fix the steering wheel (2) pulling until it is connected with the steering column (1).
2. Secure the steering wheel (2) by means of the socket pin (3); put the socket pin through
the openings (at the steering column and steering wheel)
The openings at the steering wheel and at the steering column must be in exact
alignment.

6 - CUTTING DEVICE WITH MULCHING DEFLECTOR OR SIDE DISCHARGE

The rider unit has been equipped with a cutting device Mulching type already assembled.
IN order to use it as a side discharge it is enough to unscrew the nuts (3) , disassembled
the corresponding washers (4) , the cover (1) and change the last one with the deflector
(2) . Then block the assembly with the nuts again (3) and the washers (4).
Before the cutting height is adjusted, the engine must be switched off and the
blades must have come to complete standstill.

2 - DESCRIPTION

6 Throttle lever
7 Battery
8 Blade coupling lever
9 Brake/clutch pedal
10 Brake lever

3 - TECHNICAL DETAILS

Height
265 mm
360 mm
Seat, steering wheel, front wheels and
PETROL MOWER WORKING HOURS
Show respect for those living nearby and avoid using in afternoon rest period, evening or Sundays.

4- FRONT WHEEL ASSEMBLY

5 - ASSEMBLY

7 - ADJUSTING THE CUTTING HEIGHT

(Fig.1)
Mod. 71
Briggs & Stratton 10,5 Hp IC OHV
Electric
Five forward gears and one reverse gear
7,0 Km/h
1600 mm x 820 mm x 1020 mm
Polypropylene
Sheet steel
71 cm
Centralised on 5 positions
0,7 m
Width
85 mm
120 mm
172 kg
side discharge deflector
100 dB(A)
Monday to Saturday
08.00 - 12.00 h
15.00 - 19.00 h
(Fig.3)
Attention: Assemble the wheel with valve outwards
(Fig.4)
SEAT ASSEMBLY
1- Fasten the seat (4) to the support plate (5) through the 4 M8x18 screws. Assembly with 4
washers Ø 9x24 and 4 groovers.
2- Before tightening the screws, adjust the position of the seat on the holes of the plate
according to the user's needs.
Check at regular intervals that the nuts are tightly screwed down.
Please always work with the deflector assembled or the mulching cover.
(Fig.2)
ADJUSTMENT
1. Push the adjustment lever (5) outwards in order to release it from its seat.
2. Push the lever into the required notch for the cutting height.
3. Release the lever slowly till it sticks in the notch.
The cutting height is now set.
16
11 Drive pedal
12 Agjusting levers for cutting height
13 Motor safety houding
14 Pilot light for check-in
15 Protection casing battery/engine
Recommended pressure
1,5 bar
2 bar
(Fig.5)