Lutron EcoSystem C5-BMJ-16A Guide D'installation page 4

EcoSystem Power Module Junction Box Mount | Install Guide
TM
Occupant Sensor Wired to Power Module
Multiple Fixture Dimming Control
Contrôle de gradation de multiples luminaires
Control atenuador de múltiples lámparas
C5-BMJ-16A
Power Indicator (PWR) Indicateur de puissance (PWR) Indicador de Alimentación (PWR)
On: Unit is powered
On: l'unité est alimentée Encendido: unidad tiene corriente
Off: Unit is not powered Apagado: unidad no tiene corriente
Off: l'unité n'est pas alimentée
or is malfunctioning o no está funcionando correctamente
ou est dysfonctionnelle
Status Indicator (STAT) Indicateur d'activité (STAT) Indicador de estado (STAT)
Solid: Circuit Level Plein: Niveau de circuit Sólido: Nivel del Circuito
Pulse: No communication Impulsion: Aucune Pulsante: No hay comunicación
communication
EcoSystem
Class 2 Sensors
TM
Class 2 Link
Capteurs Classe 2
PWR STAT
Lien Classe 2
Sensores Clase 2
Enlace Clase 2
Black
Red
Blue
EcoSystem Daylight Sensor & Wallstation wired
to the Power Module (IR wired only to keypad)
Multiple Fixture Dimming Control
Contrôle de gradation de multiples luminaires
Control atenuador de múltiples lámparas
C5-BMJ-16A
Power Indicator (PWR) Indicateur de puissance (PWR) Indicador de Alimentación (PWR)
On: Unit is powered On: l'unité est alimentée Encendido: unidad tiene corriente
Off: Unit is not powered
Off: l'unité n'est pas alimentée Apagado: unidad no tiene corriente
or is malfunctioning o no está funcionando correctamente
ou est dysfonctionnelle
Status Indicator (STAT) Indicateur d'activité (STAT) Indicador de estado (STAT)
Solid: Circuit Level Plein: Niveau de circuit Sólido: Nivel del Circuito
Pulse: No communication Impulsion: Aucune Pulsante: No hay comunicación
communication
EcoSystem
Class 2 Sensors
TM
Class 2 Link
Capteurs Classe 2
PWR STAT
Lien Classe 2
Sensores Clase 2
Enlace Clase 2
Black
Red
White
Yellow
EcoSystem Daylight Sensor wired
to the Power Module
Multiple Fixture Dimming Control
Contrôle de gradation de multiples luminaires
Control atenuador de múltiples lámparas
C5-BMJ-16A
Power Indicator (PWR) Indicateur de puissance (PWR) Indicador de Alimentación (PWR)
On: Unit is powered On: l'unité est alimentée Encendido: unidad tiene corriente
Off: Unit is not powered Off: l'unité n'est pas alimentée Apagado: unidad no tiene corriente
or is malfunctioning
ou est dysfonctionnelle o no está funcionando correctamente
Status Indicator (STAT) Indicador de estado (STAT)
Indicateur d'activité (STAT)
Solid: Circuit Level Plein: Niveau de circuit Sólido: Nivel del Circuito
Pulse: No communication Impulsion: Aucune Pulsante: No hay comunicación
communication
EcoSystem
TM Class 2 Sensors
Class 2 Link
Capteurs Classe 2
PWR STAT
Lien Classe 2
Sensores Clase 2
Enlace Clase 2
Black
Red
White
Yellow
4 | Lutron
®
www.lutron.com/ecosystem
Step 6: Addressing the Power Module
(Flash Mode)
• Follow standard procedure for addressing the
EcoSystem Bus
• Each Power Module communicates to the system the
same as an EcoSystem ballast; representing (1)
address location on the EcoSystem Bus
• Flash Mode (during addressing/programming):
• C5-BMJ-16A: Device will flash the load(s) by
dimming the lights up and down similar to
EcoSystem ballasts.
• C5-XPJ-16A: Device will flash the load(s) by turning
the loads ON and then OFF slowly (non-dim loads).
Do not use this module for HID loads as it may
damage the lamps.
• STAT and LED will flash at same rate as the loads.
Step 7: Troubleshooting
M M o o d d u u l l e e n n o o t t r r e e s s p p o o n n d d i i n n g g
If the module, attached ballasts, and lamps are fixed at
full light output, will not dim, and can not be turned off,
the Power Module is likely in emergency mode or not
communicating. If there is no communication, the
status (STAT) LED will blink. Verify the EcoSystem Bus
wiring is properly terminated, powered via the
EcoSystem Bus Power Supply, and 18 V
between the E1 & E2 terminals on the Power Module.
L L i i g g h h t t s s N N o o t t D D i i m m m m i i n n g g
If the lights only switch between off and full light output:
A. Verify the wiring between the module and the ballast.
B. Verify the device is a C5-BMJ-16A, as the
C5-XPJ-16A does not offer dimming control.
L L i i g g h h t t s s S S t t a a y y a a t t L L o o w w - - E E n n d d
A. Make sure Dimmed Hot is connected
(C5-BMJ-16A only).
B. If most of the ballasts are at low-end and one or
more ballasts are OFF, there is a miswire between
Hot and Dimmed Hot at one of the ballasts that is
OFF. Verify wiring.
©2008 Lutron Electronics Co., Inc.
P/N: 032-183 Rev. A 2/08
Lutron World Headquarters: +1-610-282-3800
is present
Made and Printed in the U.S.A.