Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
• Setting the IonGen
– Turn on the pump
and plug in the
IonGen
System.
™
– Adjusting the
IonGen
System's
™
Level – Depress the
"+" or "-" button
for 3 seconds to
enter the setting
mode. Once in the
setting mode the
ionization level can
be adjusted. The
setting mode will
exit automatically
– Operating the
IonGen
™
System
on a new water
feature or a water feature with good water quality – Set
the IonGen
™
System to level 1 or 2.
water quality begins to diminish.
IMPORTANT: Operate the IonGen
level and only raise the ionization level if the water
quality diminishes or the debris attached to rocks and
gravel becomes excessive. Maintaining the IonGen
System on the low level will make sure the copper
levels don't become too elevated, and also prolong
the life of the IonGen
NOTE: It is not unusual to have low, or even no copper level
readings on the test kit, no matter how high the IonGen
System's ionization level setting. This is due to the copper
being used within the water feature. Periodic copper testing will
ensure that the levels are below the maximum level of .25 ppm.
Operating the IonGen
feature with poor water quality or a lot of debris present
Set the IonGen
™
System to the highest
ionization level possible.
In some water feature
applications you may
find that you are not able
to raise the ionization
level to the higher power
setting (levels 7-10). This
is typically due to the water chemistry of the water feature or
the water flow rate across the IonGen
the IonGen
System will still produce sufficient quantity of
™
ions. Be patient, as it may take several days to a few weeks
for noticeable results to occur. Using the included copper
test kit, test the water over a period of days to ensure that
the copper levels DO NOT rise above .25 ppm. The ionization
level can be lowered once the water quality has improved or
6
System's Level
™
Follow the next step if
™
System at a low
Probe.
™
System on an existing water
™
™
Probe. In most cases,
☎
the copper test kit indicates a maximum level of .25 ppm.
– Pre-existing poor water conditions, as well as the volume of
water in the water feature are all factors that affect the speed
at which the IonGen
– If the level of copper rises above .25 ppm, reduce
the IonGen
IonGen
™
System until the copper levels fall below .25
ppm. A water change can also be conducted if the
copper levels are significantly above .25 ppm.
– In the case of a power failure the IonGen
Control Panel's internal memory will reset itself to the last
setting before the power failure.
Maintenance
IonGen
Probe Maintenance
™
• The replaceable IonGen
seasons, depending on the usage, quantity of water and
water chemistry of the water feature. The IonGen
Control Panel display
will read "00" when
the IonGen
™
completely exhausted
or there is a fault in
the operation of the
system.
™
• It is recommended to
visually inspect the bars
on the IonGen
IonGen
Probe if the bars are significantly worn.
™
• The Aquascape IonGen
in, self-cleaning mechanism that reduces the build-up of
™
oxidation scale on the bars, but requires sufficient water
flow to work properly. An excessive build-up of scale on the
bars is an indicator that there may not be sufficient water
flow. Significant oxidation scale on the bars will decrease
the distribution of ions being released into the water, as well
as affect the ability to raise and lower the Control Panel's
ionization level. Scale build-up can easily be brushed or
scraped off the bars, immediately improving IonGen
performance. If you notice repeated scale build-up, you
may want to move the IonGen
higher water flow, such as plumbing it directly into the main
recirculating system.
• Starting out each year with a new IonGen
recommended and will significantly boost the performance
of the IonGen
Winterization Maintenance
• It is recommended to shut down the IonGen
in regions that have climates that experience cold
temperatures. This will prevent elevated copper levels and
will prolong the life of the IonGen
US 1-866-877-6637 |
CAN 1-866-766-3426 | www.aquascapeinc.com
☎
System will achieve desired results.
™
System down to level one or unplug the
™
™
Probe will typically last 1 or more
Probe is
Probe from time to time, and replace the
™
™
System does contain a built-
™
Probe to a location with
System.
™
Probe.
™
System
™
™
System
Probe
™
Probe is
™
™
System
Publicité
Table des Matières
