Recommendations For Use - jbc DD 5700 Manuel D'instructions

ENGLISH
DD 5700 digital dual station
- DD 5700 230V
- DD 5700 120V
- DD 5700 100V
This unit allows you to connect and work with
2 tools simultaneously.
You can connect this unit to all the tools of our
Advanced series
corresponding stand, including the DR 5650
desoldering iron by adding the electric
desoldering pump MS 9014 Ref. 9014000 or the
air pressure desoldering system MS 9015 Ref.
9015000.
The station's components:
DD 5700 230V Ref. 5700200
- DD 5700 230V control unit
- Connection cable to mains
- Instructions manual
DD 5700 120V Ref. 5700100
- DD 5700 120V control unit
- Connection cable to mains
- Instructions manual
DD 5700 100V Ref. 5700110
- DD 5700 100V control unit
- Connection cable to mains
- Instructions manual
Kit DD 5700 -2245/DR 5650 230V Ref.5700230
- DD 5700 230V control unit
- MS 9014
electric desoldering pump
- DR 5650 desoldering iron
with the 5600-003 tip
- 2245 handpiece
- DR 8500 desoldering iron stand Ref. 0788500
- AD 8245 soldering iron stand
- 2245-003 cartridge
- 2245-006 cartridge
Kit DD 5700 -2245/PA 1200 230V Ref.5700232
- DD 5700 230V control unit
- 2245 handpiece
- PA 1200 micro hot tweezers
- AD 8245 soldering iron stand
- PA 8110 hot tweezers stand
- 2245-003 cartridge
- 1200-002 cartridge (2 units)
Speak to your distributor for more kits.
Ref. 5700200
Ref. 5700100
Ref. 5700110
but always using
Ref. 0269300
Ref. 0269320
Ref. 0269320
Ref. 5700200
Ref. 9014000
Ref. 5650000
Ref. 2245000
Ref. 0788245
Ref. 2245003
Ref. 2245006
Ref. 5700200
Ref. 2245000
Ref.1200000
Ref. 0788245
Ref. 0748110
Ref. 2245003
Ref. 1200002
Technical specifications
- Temperature selection from 90 to 450°C or
190 to 840°F (±5%).
- Power: 150W.
- Safety transformer, red separator and double
isolation, with an integrated temperature
protection fuse.
- DD 5700 230V control unit
its
Input: 230V 50Hz. Output: 24V.
- DD 5700 120V control unit
Input: 120V 60Hz. Output: 24V.
- DD 5700 100V control unit
Input: 100V 60Hz. Output: 24V.
- Total weight of unit: 6Kg (13,25lbs).
- ESD protected housing "skin effect".
Typical surface resistance: 10
square.
- Complies with CE standards on electrical
safety, electromagnetic compatibility and
antistatic protection.
- Equipotential connector and the tool tip are
connected to station mains ground supply for
ESD protection.
This product should not be thrown in the
garbage.

RECOMMENDATIONS FOR USE

For soldering and desoldering
- Clean the contacts and the printed circuit
to be desoldered of dust or dirt.
- Preferably select a temperature below
350°C (662ºF). Excess temperature may
cause the printed circuit tracks to break
loose.
- The tip must be well tinned for good heat
conduction. If it has been inoperative for
any length of time, it should be retinned.
Safety measures
- Incorrect use of this tool may cause fire.
- Be cautious when using the tool in places
where inflamable products are stored.
- Heat can cause fire to inflamable products
even when they are not in sight.
- Do not use when the atmosphere is
explosive.
- Place the tool back on its stand in order to
let it cool down before you store it.
2
Ref. 5700200
Ref. 5700100
Ref. 5700110
5 11
-10 Ohms/