Briteq BEAMBAR10-RGBW Mode D'emploi page 8

ENGLISH
[SLAVE MODE]
Used to set the projector as slave in a master/slave setup.
 Press the [MODE] or ↑/↓buttons until SLAVE MODE is showing on the display.
 Connect the projector to a master.
Note: only to be used when the DMX-line is exclusively equipped with the same projector models.
[SOUND MODE]
Used to set the projector to standalone sound mode with different chases playing in endless loops.
Press the [MODE] or ↑/↓buttons until "SOUND MODE" is shown on the display.
 Press the [ENTER] button: the sensitivity of the microphone (SENS) can be set from 00 to 31.
 Use ↑/↓ buttons to change the value.
 Press the [ENTER] button: the repetition rate (REP) of the chases can be set from 00 to 99.
 Use ↑/↓ buttons to change the value.
[AUTO RUN] (SIMPLE AUTO MODE)
Used to set the projector to standalone auto mode with different chases playing in endless loops.
Press the [MODE] or ↑/↓buttons until "AUTO RUN" is shown on the display.
 Press the [ENTER] button: the playback speed of the chases can be set from 00 to 99.
 Use ↑/↓ buttons to change the value.
 Press the [ENTER] button: the repetition rate (REP) of the chases can be set from 00 to 99.
 Use ↑/↓ buttons to change the value.
][EFFECT MODE]
Used to set the desired effect mode while used as master.
 Press the [MODE] or ↑/↓buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ↑/↓ buttons to selected the desired mode: 01. to 13.XXXXX: (different chases, including color fade,
color change, effects, ...)
 Once the correct option shows on the display, press the [ENTER] button to save it.
 Use ↑/↓ buttons to select the desired playback speed from 01 (very slow) to 99 (fast).
 Once the correct value shows on the display, press the [ENTER] button to save it.
 Use ↑/↓ buttons to select the desired strobe speed from 00 (NO strobe) to 99 (fast).
 Once the correct value shows on the display, press the [ENTER] button to save it.
[FLOW INVERT MODE]
Used to change the running direction of the chases.
 Press the [MODE] or ↑/↓buttons until "FLOW INVERT" is shown on the display.
 Use ↑/↓ buttons to toggle between ON and OFF.
[STATIC COLOR MODE]
Used to set the desired fixed color while used as master: 9 preset colors + 1 custom color.
 Press the [MODE] or ↑/↓buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ↑/↓ buttons to selected the desired color:
 COLOR WW
 COLOR CW
 RED
 ORANGE
 YELLOW
 GREEN
 CYAN
 BLUE
 PURPLE
 COLOR SET
 Press the [ENTER] button: the display shows the value (000-255) for RED. (change with ± buttons)
 Press the [ENTER] button: the display shows the value (000-255) for GREEN. (change with ± buttons)
 Press the [ENTER] button: the display shows the value (000-255) for BLUE. (change with ± buttons)
 Repeat these steps until you have the desired values. The settings will be automatically saved.
BRITEQ
®
warm white 3200K
warm white 5600K
this is a color that can be set by the user. Follow these steps:
6/84
OPERATION MANUAL
BEAMBAR5+10-RGBW