Installation Instructions - DSC WTK5504 Instructions D'installation

Installation Instructions

The WTK5504 2-Way Wireless Keypad is com-
patible with the Alexor PC9155 and Impassa
SCW9055/57 wireless panels. The WTK5504
can be used with PowerSeries v4.6+ and
TR5164.
Specifications
• Operating temperature range: 0°C to 49°C (32°F
to 120°F)
• Humidity (MAX): 93% R.H. non-condensing
• Power adapter output voltage: 9V
Adapter Models: US/Latin America -
9VADAPTER-US; Canada: 9VADAPTER-CAN
• Battery pack: NiMH rated 4.8V, 2.1Ah, Model
4PH-H-AA2100-S-D22 UL listed (DSC P/N
17000153).
• WTK5504 Input ratings: 9VDC/200mA
(standby) / 300mA (maximum, alarm condi-
tion). Use only in conjunction with the provided
power adapter.
• Wall-mount and case tampers.
• Touchscreen display: 4.3" WVGA
• Horizontal viewing angle: 130°
• Vertical viewing angle: 70° top, 70° bottom
2
• Brightness: 400cd/m
• Voice chime and prompting
• Ready, Armed, Trouble, and AC status LEDs
• Proximity tag support (WTK5504P only)
• "Night" light with adjustable brightness
• Frequency: 433.92MHz
NOTE: When the power adapter is used, the
battery pack provides minimum 24h back-up.
NOTE: The WTK5504 can be used in UL/
ULC listed residential fire and burglary instal-
lations with all compatible control panels.
NOTE: The WTK5504 can be used in UL/
ULC listed commercial burglary installations
with Power series models PC1864, PC1832
and PC1616.
NOTE: UL/ULC commercial burglary instal-
lations require the enabling of tamper detec-
tion.
Handling
• Do not subject the touchscreen to mechanical
shock (e.g., dropping or striking).
• If the touchscreen glass is damaged, the liquid
crystal fluid inside could leak out. Avoid contact
with the liquid crystal fluid. If the liquid crystal
fluid comes into contact with your skin or
clothes, promptly wash it off using soap and run-
ning water. Seek medical care.
• Do not apply excessive force to the display sur-
face or adjoining areas. Excessive force will dis-
@ 1.25A
DC
tort the image on the display.
• Do not use hard or sharp implements to operate
the touchscreen. Operating the touchscreen with
any implement harder than a finger could
scratch the display.
Installation
• The WTK5504 must be installed by a Service
Person.
• The WTK5504 contains components that could
be damaged by static electricity. To prevent
damage to the WTK5504, installers and tools
must be grounded during installation. Take extra
care when working in low humidity conditions.
• The touchscreen is covered by a film to protect
the display during installation. Wear a grounding
strap and remove the protective film slowly to
prevent the generation of static electricity that
may damage the display.
• When installing the WTK5504, avoid locations
in direct sunlight or close to fluorescent lights.
Unpacking
The WTK5504 keypad package is available in
four configurations. The contents of each pack-
age are described below.
WTK5504P - DESK WTK5504P - WALL
STAND/PROX TAG MOUNT/PROX TAG
• WTK5504P Keypad • WTK5504P Keypad
• WTK5504DMK • WTK5504BRK Wall
Desk Stand Bracket
• Installation Manual • Installation Manual
• User Manual • User Manual
• NiMH Battery Pack • NiMH Battery Pack
(installed) (installed)
• Power Adapter • Power Adapter
• Hardware Pack • Hardware Pack
• PT4 Prox Tag • PT4 Prox Tag
(433MHz) (433MHz)
• PT4 Manual • PT4 Manual
WTK5504 - DESK WTK5504 - WALL
STAND
• WTK5504 Keypad • WTK5504 Keypad
• WTK5504DMK • WTK5504BRK Wall
Desk Stand Bracket
• Installation Manual • Installation Manual
• User Manual • User Manual
• NiMH Battery Pack • NiMH Battery Pack
(installed) (installed)
• Power Adapter • Power Adapter
• Hardware Pack • Hardware Pack
Replacement battery pack and additional prox-
imity tags are available separately.
Powering
Apply Battery Power
1.Insert a small, flat screwdriver into the two
slots on the back of the keypad and release
both latches (see diagram).
2. Remove the back cover by opening from the
top and pivoting open the case.
MOUNT