Specified Conditions Of Use - Milwaukee M12 FDGA Notice Originale

Do not let any metal parts enter the airing slots - danger of short
circuit!
Always use and store accessories according to the manufacturer's
instructions.
WARNING! Danger of burns! The wheel and workpiece will
become hot during use. Wear gloves when changing discs or
touching workpiece. Keep hands away from the grinding area at
all times.
WARNING! To reduce the risk of re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in uid or allow a uid to ow inside them.
Corrosive or conductive uids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc., Can
cause a short circuit.
Do not use this tool to work on asbestos-containing products.
Determine the composition of the workpiece before beginning
work. Asbestos should only be removed by a quali ed professional.
The insertion tool must be clamped at least 10 mm. The inner shank
dimension L can be used to calculate the maximum permitted
speed of the insertion tool from the speci cations provided by
manufacturer of the insertion tool. It must not be less than the
GB
maximum speed of the power tool.
The workpiece must be xed if it is not heavy enough to be steady.
Never move the workpiece towards the rotating insertion tool by
hand.
Remove dust and debris from the collet body and clean the inser-
tion tool mandrel before inserting it.
Insertion tools should be protected from:
• wetness and extreme humidity
• any type of solvent
• extreme changes in temperature
• dropping and bumping
Insertion tools should be stored
• in an organized way so the insertion tools can be removed
without disturbing or damaging other insertion tools
• with their safety information
Insertion tools should NOT be dropped, rolled or bumped.
Discard insertion tools that have been dropped, rolled, bumped,
subjected to extreme changes in temperature, or come into contact
with solvents or wetness.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Use only System M12 chargers for charging System M12 battery
packs. Do not use battery packs from other systems.

SPECIFIED CONDITIONS OF USE

The die grinder is intended for grinding, cutting, polishing and wire
brushing of wood, plastic and metal. It is ideally suited for working
on hard to reach areas.
Please refer to the instructions supplied by the accessory
manufacturer.
The machine is suitable only for working without water.
Do not use the product in any way other than those stated for
intended use.
English
14
BATTERIES
Temperatures in excess of 50°C (122°F) reduce the performance of
the battery pack. Avoid extended exposure to heat or sunshine (risk
of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully char-
ged, after use. Battery packs which have not been used for some
time should be recharged before use.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days Store the battery pack
where the temperature is below 27°C and away from moisture
Store the battery packs in a 30% - 50% charged condition Every six
months of storage, charge the pack as normal.
Do not dispose of used battery packs in the household refuse or
by burning them. Milwaukee Distributors o er to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit
situations that cause high current draw, the tool will stop for about
2 seconds and then the tool will turn OFF. To reset, remove the
battery pack from the tool and replace it.
Under extreme circumstances, the internal temperature of the
battery pack could raise too much. If this happens, the fuel gauge
will ash until the battery pack cooled down. After the lights go o ,
the work may continue. Place the battery on the charger to charge
and reset it.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legisla-
tion requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
The user can transport the batteries by road without further
requirements.
Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation and
transport are exclusively to be carried out by appropriately trained
persons and the process has to be accompanied by corresponding
experts.
When transporting batteries
Ensure that battery contact terminals are protected and insulated
to prevent short circuit. Ensure that battery pack is secured against
movement within packaging. Do not transport batteries that are
cracked or leak. Check with forwarding company for further advice
LOAD DEPENDENT MOTOR PROTECTION
If the battery becomes too hot, the fuel gauge lights will ash in
an alternating pattern and the tool will not run. Allow the battery
to cool down.