Specified Conditions Of Use; Mains Connection; Ec Declaration Of Conformity - Milwaukee AG 11-115 Notice Originale

Appliances used at many diff erent locations including open air should be
connected via a residual current device (FI, RCD, PRCD) of 30mA or less.
Sawdust and splinters must not be removed while the machine is running.
Only plug-in when machine is switched off .
Never reach into the danger area of the plane when it is running.
Always use the auxiliary handle.
Immediately switch off the machine in case of considerable vibrations or if
other malfunctions occur. Check the machine in order to fi nd out the cause.
Always use and store the grinding disks according to the manufacturer's
instructions.
When grinding metal, fl ying sparks are produced. Take care that no persons are
endangered. Because of the danger of fi re, no combustible materials should be
located in the vicinity (spark fl ight zone). Do not use dust extraction.
Due care should be taken that no sparks or sanding dust fl ying from the
workpiece come into contact with you.
When separating stone the guide shoe must be used!
The adjusting nut must be tightened before starting to work with the machine.
The adjusting nut must be tightened before starting to work with the machine.
The workpiece must be fi xed if it is not heavy enough to be steady. Never lead the
workpiece to the grinding disk with your hand.
Under extreme conditions (e.g. smooth-grinding metals with the arbour and
vulcanized fi bre grinding wheel), signifi cant contamination can build up on the
inside of the angle grinder. For safety reasons, in such conditions the inside should be
cleaned thoroughly of metal deposits and a motor circuit-breaker must be connected
in series. If the motor circuit-breaker trips the machine must be sent for repair.
For accessories intended to be fi tted with threaded hole wheel, ensure that the
thread in the wheel is long enough to accept the spindle length.
Use the safety guard from the accessories range when performing out cutting
work.

SPECIFIED CONDITIONS OF USE

The angle grinder may be used for cutting, grinding and wire brushing a wide
range of materials, such as metal or stone. If you have any doubts, please refer
to the instructions supplied by the accessory manufacturer.
Do not use this product in any other way as stated for normal use.

MAINS CONNECTION

Connect only to single-phase AC current and only to the system voltage
indicated on the rating plate. It is also possible to connect to sockets without an
earthing contact as the design conforms to safety class II.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in conformity with
the following standards or standardized documents. EN 60745, EN 55014-1,
EN 55014-2, EN 61000-3-2, EN 61000-3-3, in accordance with the regulations
2006/42/EC, 2004/108/EC
Winnenden, 2010-07-22
Rainer Kumpf
Manager Product Development
Authorized to compile the technical fi le
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Do not let any metal parts reach the airing slots - danger of short circuit!
Use only Milwaukee accessories and spare parts. Should components need to be
replaced which have not been described, please contact one of our Milwaukee
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
Article No. as well as the machine type printed on the label and order the
drawing at your local service agents or directly at: Milwaukee Electric Tool,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before
starting the machine.
CAUTION! WARNING! DANGER!
Always wear goggles when using the machine.
Always disconnect the plug from the socket before
carrying out any work on the machine.
Accessory - Not included in standard equipment,
available as an accessory.
Do not dispose of electric tools together with
household waste material! In observance of
European Directive 2002/96/EC on waste electrical
and electronic equipment and its implementation
in accordance with national law, electric tools that
have reached the end of their life must be collected
separately and returned to an environmentally
compatible recycling facility.
GB
English
13