1. Manuels
  2. Marques
  3. LUND Manuels
  4. Accessoires de voiture
  5. 26410017
  6. Instructions d'installation

LUND 26410017 Instructions D'installation

For toyota tundra
Masquer les pouces
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Télécharger ce manuel
For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219.
Important Safety Information
• To be used with Lund® branded products only.
• Do not stand on Lund running board or bracket while vehicle is in motion.
• Do not use the brackets as a jacking point for the vehicle.
• Do not use the bracket system or running boards to fasten cargo.
• Periodically check all components for tightness.
• Be sure to wear safety glasses while installing brackets.
•When using power tools, read and understand all operating instructions.
Contents
NOTE: Actual product may vary from illustration.
Driver Side Rock Rail
Tools Required
Ratchet and Extension
Preparation Before Installation
• Park your vehicle in a clean, level location. Check to make sure the vehicle is in park, or for manual drive models, place the
transmission in first gear. Engage the parking brake. Chock wheels.
• Unpack the kit and identify the parts according to the content descriptions.
• An assistant is recommended to help position the running board properly during the installation.
Installation Steps
Identify the (3) mounting locations for each running board bracket by looking under the driver side of the vehicle and finding the holes
in the rocker panel. Note which holes correspond with the holes in the running board brackets. Mark the holes in the rocker panel with a
1
Installation Instructions
Rock Rail for Toyota Tundra
For proper installation and best possible fit, please read all instructions BEFORE you begin.
Passenger Side Rock rail
Socket Set
NOTE: Actual application may vary slightly from illustrations.
8mm hex bolt
(12)
Wheel Chocks
grease pencil.
Front passenger side shown
Page 1 of 3
I - Sheet Number LUNDRB33 Rev.A
Lund Part# 26410017
8mm flat washer
8mm lock
(12)
washer (12)
Safety Glasses
26410018

Publicité

Table des Matières
loading

Manuels Connexes pour LUND 26410017

Sommaire des Matières pour LUND 26410017

  • Page 1 Important Safety Information • To be used with Lund® branded products only. • Do not stand on Lund running board or bracket while vehicle is in motion. • Do not use the brackets as a jacking point for the vehicle.

  • Page 2: Installation Steps

    Installation Steps NOTE: Actual application may vary slightly from illustrations. Beginning on the driver side, remove plastic plugs or factory hex Align running board brackets so that the slots in the bolts (if equipped). Repeat for remaining mounting locations. brackets align with the holes from Step 2. Partially (Figure 1) attach Front Mounting Bracket to the vehicle using (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm...

  • Page 3: Care And Cleaning

    You have purchased one of the many quality Lund branded products offered by Lund International, Inc. We take the utmost pride in our products and want you to enjoy years of satisfaction from your investment. We have made every effort to ensure that your product is top quality in terms of fit, durability, finish and ease of installation.

  • Page 4: Consignes De Sécurité Importantes

    • À n'utiliser qu'avec des produits de la marque Lund®. • Ne pas se tenir sur le support ou le marchepieds Lund lorsque le véhicule est en déplacement. • Ne pas utiliser les supports comme point de levage pour le véhicule.

  • Page 5: Étapes De L'installation

    Étapes de l'installation REMARQUE : l'installation réelle peut différer légèrement des illustrations. En commençant par le côté passager, retirer les bouchons Alignez Running Board supports de manière à ce que les fentes dans les supports se alignent avec les trous de l’étape en plastique ou les boulons à...

  • Page 6: Entretien Et Nettoyage

    Félicitations! Vous venez d'acheter un des nombreux produits de qualité de la marque Lund® fabriqués par Lund International, Inc. Nous sommes extrêmement fiers de la qualité de nos produits et nous espérons que vous profiterez de cet investissement de longues années durant.

  • Page 7: Herramientas Necesarias

    Información importante de seguridad • Para usar solo con productos de Lund®. • No se pare sobre los estribos o soportes Lund cuando el vehículo está en movimiento. • No use los soportes como punto de apoyo del vehículo. • No use el sistema de soportes o los estribos para sujetar la carga.

  • Page 8: Pasos De Instalación

    Pasos de instalación NOTA: La aplicación real tal vez no sea igual a las ilustraciones. Comenzando por el lado del acompañante, retire los tapones de Alinear corriendo soportes de mesa para que las ranuras de plástico o pernos hexagonales incluidos de fábrica los soportes estén alineados con los agujeros de la Etapa (si están incluidos).

  • Page 9: Cuidado Y Limpieza

    ¡Felicitaciones! ® Usted ha adquirido uno de los tantos productos de marca de calidad Lund que ofrece Lund International, Inc. Nos enorgullecen mucho nuestros productos y deseamos que disfrute años de satisfacción por su inversión. Nos hemos esforzado mucho para asegurarnos de que su producto sea de gran calidad en cuanto a ajuste, durabilidad, acabado y facilidad de instalación.

Ce manuel est également adapté pour:

26410018

Table des Matières